manualshive.com logo in svg

Beastx Aircraft, Instruction Manual, Page: 12 / 88

Share
Download
Beastx Aircraft Instruction Manual Download Page 12

12 

3 .2 Preparing a transmitter for flybarless 

(This step is unnecessary when using the MICROBEAST with the optional cable for stand-alone tail gyro use. 

Please see 4.1.2)

First create a new model in your radio‘s model memory. When using the MICROBEAST you have to disable 

any mixing functions for the swashplate or tail. Each function should be assigned to just one receiver chan-

nel. As you see our requirement for the transmitter is very low.

Be sure that all trims and sub trims are disabled and that all servo travel are 100% (increasing or decreasing 

the servo travel for aileron, elevator and rudder can later adjust the maximum control rates, see chapter 9-

B

 ).

Never enable your radio‘s eCCPM mixing function: this will be done by the MICROBEAST. Always set your 

radio‘s swash mixer to mCCPM (mechanical mixing) which is often called “H1” or “1 servo” mixing.

Do not adjust the pitch curve at the moment. For the setup procedures, it has to be set as a straight line from 

-100% to +100% (or 0 to 100% depending on radio brand).

Again make sure that there are no mixing functions active (for example revo-mixing).

Other functions such as throttle curves, ESC switches or auxiliary functions can be adjusted as usual.

Summary of Contents for Aircraft

























































































Reviews:

No comments