manualshive.com logo in svg

Beastx Aircraft, Instruction Manual, Page: 41 / 88

Share
Download
Beastx Aircraft Instruction Manual Download Page 41

41 

Please note that depending on the tail servo center position pulse length chosen at setup menu point 

C

, you 

may not be able to choose a frequency higher than 333Hz. This also applies to the “

user defined

“ setting which 

might be limited to 333Hz (see also note at setup menu point 

C

).

If you do not know what the maximum frequency tolerated by your servo is, please select not more 

then 50Hz . A higher frequency can lead to failure of the servos!  

Analog Servos usually tolerate only 50Hz. Digital servos usually allow higher frequencies, but this has to 
be verified in the datasheet of the servo. You may need to check with the manufacturer of the servos. 

On 

WWW .beASTX .COM

 you can find a list of parameters for the most common servos.

D

 Tail servo frequency

As with the swashplate servos at setup menu point 

B

 you can select at setup menu point 

D

 the 

frequency for the tail servo.

To optimize the performance of the MICROBEAST tail gyro, the rule is the higher the better! 

A good rudder servo should be capable of running at least 270Hz.

By moving the tail stick 

repeatedly in one direction you 

can choose the desired tail servo 

frequency.

Status-LeD

Tail servo frequency 

purple

50 Hz *

red 

flashing

165 Hz

red

270 Hz

blue 

flashing

333 Hz

blue

560 Hz

off

User defined

*

 Factory Setting

Summary of Contents for Aircraft

























































































Reviews:

No comments