manualshive.com logo in svg

Beastx Aircraft, Instruction Manual, Page: 37 / 88

Share
Download
Beastx Aircraft Instruction Manual Download Page 37

37 

A

 Mounting orientation of the MICRObeAST

The MICROBEAST unit can be mounted in nearly all possible orientations. The only restriction is that 

the plug connectors have to point in or against flying direction (see chapter 3).

 

At setup menu point 

A

, you have to choose whether the MICROBEAST is mounted horizontally (prin-

ted surface 90 degrees to the main shaft) or vertically (printed surface in parallel with the main shaft). 

The color of the Status-LED shows the currently selected orientation:

Status-LeD

Mounting orientation

red

vertical (on the side)

blue

horizontal (flat)*

*

 Factory Setting

As already described (Fig. 18) you can switch between the two options by moving the rudder stick to 

one or other direction. For checking purposes the Status-LED will change color.

Push the button to save the configuration and to proceed to setup menu point 

B

 .

Fig. 20

Status-LED:

 blue

Status-LED:

 red

Summary of Contents for Aircraft

























































































Reviews:

No comments