BD Diesel Performance 1036703 Instructions Manual Download

Page: 36 / 40

21 October 2011

Ford 6.7L 2011-2012 Positive Air Shutoff

BD ENGINE BRAKE, INC.

Plant Address: A10-33733 King Rd, Abbotsford, BC, Canada V2S 7M9

US Shipping Address: 88-446 Harrison St, Sumas, WA 98295 US Mailing Address: PO Box 231, Sumas, WA 98295

Phone: 604-853-6096 Fax: 604-853-8749 Internet: www.bd-power.com

3. Start the engine.

4. Press and hold the RPM SET button.

When you push the SET RPM button
will see the “RPM Set” LED illuminate.

5. With another person helping you, have

them step on the accelerator with the
vehicle in park. Raise the engine RPM
to 1200 RPM.

6. Release the SET RPM button.

Upon releasing the button the unit will
store the RPM + 25%. So for this
example the unit has stored 1320 RPM
+ 25% = 1650 RPM.

Set

Button

PRESS &

HOLD

RPM Set

RELEASE TO

STORE RPM

RPM Set

You should see the RPM signal flash
proportionally to engine RPM.

7. Now increase the RPM of the engine

to test the activation circuit is working
correctly. As in this example the valve
should activate at 1650 RPM.

You  should  see  the  ACTIVATION
LED flash ON/OFF on activation.

If  the  valve  does  not  activate  check
the wiring.

If  the  valve  activates  but  the  engine
does  not  stall,  ensure  nothing  has
contacted the valve linkage.

8. With the valve activated the engine

should die. Reset the valve and restart
the engine.

9. Press and hold the RPM SET button.

When you push the SET RPM button
will see the “RPM Set” LED illuminate.

10. With another person helping you, have

Summary of Contents for 1036703









































Search results

Summary of Contents for 1036703

Reviews:

Related manuals for 1036703

Brands by name

Popular brands

BD Diesel Performance 1036703, Instructions Manual

Search results

Summary of Contents for 1036703

Reviews:

Related manuals for 1036703

Brands by name

Popular brands