BCF Technology Ovi-Scan Instruction Manual Download Page 7 | Manualshive

Page: 7 / 28

BCF Technology Ovi-Scan Instruction Manual Download Page 7

7

2 Controls

All functions of the console are set using menus selected using keys below the screen.

2.1 Power button

The power button on the front of the pull out module is a soft power button, it does not disconnect the
power, but puts the system into a low-power, standby mode.

This button also doubles as an image freeze button (see 2.2.4 B), a short press will freeze the image, a
long press (more than 2 seconds) will power the system down.

2.2 Menu system

All functions of the Ovi-Scan are set using menus selected using the ‘soft keys’ below the screen, on
the pull out module.

Soft Key 1 (on the left) is used to cycle through the menus; the other keys are then used to access sub-
menus and settings.

The system defaults to the ‘TALLy’ menu on power up and cycles through the menus in the following
sequence: ‘DISPLAy’, ‘CONTROL’, ‘IMAGE’, ‘ELLIPSES’, ‘DRAFTING’, ‘RFID’ and ‘MODES’ before
returning to ‘TALLy’.

Ovi-Scan manual v.3.indd 7

13/07/2012 16:44

«
...
5
6
7
8
9
...
»

Summary of Contents for Ovi-Scan





























Reviews:

No comments