BCF Technology Ovi-Scan Instruction Manual Download Page 6 | Manualshive

Page: 6 / 28

BCF Technology Ovi-Scan Instruction Manual Download Page 6

6

Ovi-Scan

Operating instructions

The operating instructions are to be read with reference to Appendix E on Page 25.

1 Preliminary switch on

Before connecting or disconnecting the probe, ensure that the console power is switched off and that
both probe and console connectors are free from dirt.

Connect the probe to the front connector marked ‘PROBE’ (G).

Rotate the probe connector until the notches on the probe and scanner align, and then screw the
retaining ring clockwise to lock the connector in position.

Connect the remote tally connector (optional) to the front panel marked ‘TALLy’ (F). Rotate the
connector until the notch on the tally connector aligns with the key on the console, then tighten the
outer ring to secure.

The Ovi-Scan is designed to operate only from a 12 volts DC source.

Use only BCF supplied battery pack, vehicle adapter cable, AC adapter or portable power station.

• Check that the connector is of correct polarity.

• Connect the battery cable to connector: (K) on the rear panel of the module. Rotate connector

until the notch on the power connector aligns with the key on the console then tighten the outer
ring to secure.

• Press and hold the ‘POWER’ button (L) on the front panel until the system beeps.

The green ‘DC POWER’ light (M) should be illuminated and the console will now perform a system
initialisation.

If the probe is connected, it will start to rotate.

The sector scan and settings will be displayed on the screen.

The buzzer will sound twice; the second indicates that the system initialisation is complete and the
system is ready to function.

If the supply voltage is too low (less than 9 volts) the system will display a ‘Low Battery’ message for 6
seconds before powering down.

If the console and module cannot establish communications then the console will display a ‘CHECK DUO
COMMS’ message before switching to the Duo-Scan video input. Unclip the latches and remove the Duo-
Scan module (see 3 Module removal/refitting). Check the five contacts on the base of the Duo-Scan and
within the console are clean, and refit the Duo-Scan module.

Ovi-Scan manual v.3.indd 6

13/07/2012 16:44

«
...
4
5
6
7
8
...
»

Summary of Contents for Ovi-Scan





























Reviews:

No comments