Bauer 2161CR-B Owner'S Manual & Safety Instructions Download

Page: 12 / 20

Page 12

For technical questions, please call 1-888-866-5797.

Item 58308

FETY

OPERA

MAINTENANCE

SETUP

Installing Wheel Guard

TO PREVENT SERIOUS INJURY: Do not operate this tool without the Wheel Guard properly installed.

Note:

Grinding Wheel sold separately.

Note:

Make sure Battery Pack is removed and tool

is off before installing Wheel or Wheel Guard.

1. Depress the Spindle Lock Button and rotate

the Clamp Nut until the Spindle Locks.

2. Loosen and remove Clamp Nut from

the Spindle. Remove Disc Flange.

3. Install Wheel Guard over the Spindle.

4. Rotate the Wheel Guard as needed to

shield you during the planned work.

5. Replace Disc Flange. Make sure the flats on

bottom of the Disc Flange are engaged with

the depressed center of the Wheel Guard.

6. Check the Wheel Guard to ensure

it is firmly in place. Adjust if

necessary before proceeding.

Disc Flange

Wheel Guard

Spindle

Spindle Lock

Button

Figure A: Guard Installation

Installing Side Handle

TO PREVENT SERIOUS INJURY:

Do not operate this tool with one hand only or without the Auxiliary Handle properly installed.

1. The Side Handle can be installed on

the left, or right side of the grinder,

depending on operator preference.

2. Insert the Side Handle into the

desired operating position.

3. Turn the side handle clockwise to securely tighten.

4. Reposition Wheel Guard if necessary. Wheel Guard

should be installed opposite the Side Handle.
a. Make sure Battery Pack has been

removed and tool is off.

b. Unlock Guard Clasp by pulling

Clasp out (away from Grinder).

c. Rotate Guard to correct position.
d. Relock the Guard Clasp by pushing Clasp in.

Note:

Raised ridge on Wheel Guard should be

seated in the groove on the Bearing Cap.

Summary of Contents for 2161CR-B





















Search results

Summary of Contents for 2161CR-B

Reviews:

Related manuals for 2161CR-B

Brands by name

Popular brands

Bauer 2161CR-B, Owner'S Manual & Safety Instructions

Search results

Summary of Contents for 2161CR-B

Reviews:

Related manuals for 2161CR-B

Brands by name

Popular brands