Bauer 2161CR-B Owner'S Manual & Safety Instructions Download | Manualshive

Page: 11 / 20

background image

Page 11

For technical questions, please call 1-888-866-5797.

Item 58308

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Make sure that the Power Switch/Trigger is in the off-position and remove its

Battery Pack before performing any procedure in this section.

Note:

For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

Components

Wheel

(sold separately)

Wheel Guard

Side Handle

Power Switch

Spindle Lock Button

Battery Pack

(sold separately)

Main Handle

«
...
9
10
11
12
13
...
»

Summary of Contents for 2161CR-B





















Reviews:

No comments

Related manuals for 2161CR-B

Brand: Mahlkonig Pages: 20

Brand: Milwaukee Pages: 2

Brand: Orbegozo Pages: 37

Brand: Epiroc Pages: 12

METALWORKER CHDBG900

Brand: Clarke Pages: 16

Brand: Kogan Pages: 5

Profiline A-WKS 18V

Brand: BTI Pages: 232

Brand: Bort Pages: 33

Brand: Brave Pages: 24

Brand: Sealey Pages: 3

Brand: Sealey Pages: 3

Brand: Sealey Pages: 4

Brand: Sealey Pages: 2

Brand: Sealey Pages: 4

Brand: Sealey Pages: 3

Brand: Sealey Pages: 6

POWER TOOLS SA673

Brand: Sealey Pages: 2

Brand: Sealey Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands