Bauer 2161CR-B Owner'S Manual & Safety Instructions Download

Page: 9 / 20

Page 9

For technical questions, please call 1-888-866-5797.

Item 58308

FETY

OPERA

MAINTENANCE

SETUP

Grounding

TO PREVENT ELECTRIC SHOCK AND DEATH FROM

INCORRECT GROUNDING WIRE CONNECTION:

Check with a qualified electrician if you are in doubt as to whether the outlet is properly

grounded. Do not modify the power cord plug provided with the tool. Never remove the

grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged,

have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet

installed by a qualified electrician.

Extension Cords

Note:

Extension cords must not be used with this item’s Charger.

Symbology

Double Insulated

Volts

Alternating Current

Amperes

n0 xxxx/min.

No Load Revolutions

per Minute (RPM)

WARNING marking concerning Risk

of Eye Injury. Wear ANSI-approved

safety goggles with side shields.
WARNING marking concerning Risk

of Respiratory Injury. Wear NIOSH-

approved breathing protection rated

for the hazards in your work area.

Read the manual before

set-up and/or use.

WARNING marking

concerning Risk of Fire.

Do not cover Charger

ventilation ducts.

Charge on fireproof surface only.

WARNING marking concerning

Risk of Electric Shock.

Properly connect Charger’s power

cord to appropriate outlet.

WARNING marking concerning

Risk of Explosion.

Do not puncture, short, or open

battery packs and do not charge

damaged battery packs.

Summary of Contents for 2161CR-B





















Search results

Summary of Contents for 2161CR-B

Reviews:

Related manuals for 2161CR-B

Brands by name

Popular brands

Bauer 2161CR-B, Owner'S Manual & Safety Instructions

Search results

Summary of Contents for 2161CR-B

Reviews:

Related manuals for 2161CR-B

Brands by name

Popular brands