1. Safety
•
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet.
Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.
•
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-re
fl
ective
coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent
solution, or thinner.
•
Rated maximum ambient temperature, t
a
= 40 °C (104 °F).
•
The lamp house shall be replaced if it has become damaged or thermally deformed.
On servicing
•
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials
and risk of electric shock.
•
Refer all servicing to quali
fi
ed service personnel.
•
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can
lead to permanent damage to the projector and cancellation of the warranty.
•
Unplug this product from the wall outlet and refer servicing to quali
fi
ed service technicians under the following conditions:
-
When the power cord or plug is damaged or frayed.
-
If liquid has been spilled into the equipment.
-
If the product has been exposed to rain or water.
-
If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a quali
fi
ed technician to restore the product to normal operation.
-
If the product has been dropped or the cabinet has been damaged.
-
If the product exhibits a distinct change in performance, indicating a need for service.
•
Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement
parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitu-
tions may result in degraded performance and reliability,
fi
re, electric shock or other hazards. Unauthorized substitutions may
void warranty.
•
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
•
Possible explosion hazard: Always keep in mind the caution below:
C
AUTION
:
Xenon compact arc lamps are highly pressurized. When ignited, the normal operating temperature
of the bulb increases the pressure to a level at which the bulb may explode if not handled in strict accordance
to the manufacturer’s instructions. The bulb is stable at room temperature, but may still explode if dropped or
otherwise mishandled. Whenever the lamp house, containing a xenon lamp, has to be dismantled or whenever
the protective container or cloth has to be removed from the xenon lamp, authorized protective clothing MUST
be worn!
To prevent battery explosion
•
Danger of explosion if battery is incorrectly installed.
•
Replace only with the same or equivalent type recommended by the manufacturer.
•
For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and regulations
to ensure proper disposal.
1.3
Important warnings concerning HDF W series
fl
ight cases
Important warnings concerning stacking/transporting HDF W series rental
fl
ight cases
•
Stack maximum two (2) HDF W series rental
fl
ight cases high. Never higher.
•
Surface on which
fl
ight case is standing must be level to ensure that the total load is evenly spread out among the four wheels.
The surface must also be able to support the load safely.
•
Before stacking or transporting
fl
ight cases, check the wheels and their
fi
xation screws for wear or defects.
•
Before stacking or transporting
fl
ight cases, check that the four lock handles on each
fl
ight case are in good working order and
locked securely.
•
When stacked, make sure the wheels of the upper
fl
ight case are precisely positioned in the stacking dishes of the
fl
ight case
below.
•
Stacked
fl
ight cases may not be moved. Before stacking, the lower
fl
ight case must already be in its
fi
nal resting position before
placing the second upon it.
•
Never stack loaded
fl
ight cases in a truck or other transport medium, unless each
fl
ight case is rigidly strapped tight.
•
In the event of a wheel breaking,
fl
ight cases must be rigidly strapped tight to prevent a stack collapsing.
8
R5905158 HDF W SERIES 10/07/2012
Summary of Contents for HDF W series
