background image

15

USE  AND  CARE  INSTRUCTIONS

CORRECT LP GAS TANK USE

The  LP  Gas  tank  must  be  constructed  and  marked  in

accordance  with  the  Specifications  for  LP-Gas  Cylinders

of the  U.S. Department  of Transportation  (D.O.T.) or  the

National Standard  of Canada,  CAN/CSA-B339, Cylinders,

Spheres  and  Tubes  for  Transportation  of  Dangerous

Goods  and  Commission;  as  applicable.

The  LP Gas  tank  must have  a  shutoff valve,  terminating

in an  LP Gas supply tank  valve outlet, that  is compatible

with a Type  1 tank  connection device. The  LP Gas  tank

must  also  have  a  safety  relief  device  that  has  a  direct

connection  with  the  vapor  space  of  the  tank.

The  tank  supply  system  must  be  arranged  for  vapor

withdrawal.

The LP  Gas  tank must  have a  collar  to protect  the tank

valve.

Never  connect  an  unregulated  LP  gas  tank  to  your  gas

grill.  The  gas  regulator  assembly  supplied  with  your  gas

grill  is  adjusted  to  have  an  outlet  pressure  of  11"  water

column  (W.C.)  for  connection  to  an  LP  gas  tank.  Only

use  the  regulator  and  hose  assembly  supplied  with  your

gas  grill.  Replacement  hose  and  regulator  assembly

must  be  identical  to  those  listed  in  the  parts  list  of  this

Operator's  Manual  as  specified  by  Grand  Hall.

Have your LP Gas dealer check the relief valve after every

filling  to  ensure  it  remains  free  of  defects.

Always  keep  LP  Gas  tank  in  upright  position.

Do not subject the LP Gas tank to excessive heat.

Never  store  an  LP  Gas  tank  indoors.  If  you  store  your

gas  grill  in  the  garage  always  disconnect  the  LP  Gas

tank  first  and  store  it  safely  outside.

LP  Gas  tanks  must  be  stored  outdoors  in  a  well-

ventilated  area  and  out  of  the  reach  of  children.

Disconnected  LP  Gas  tanks  must  not  be  stored  in  a

building,  garage  or  any  other  enclosed  area.

The  regulator  and  hose  assembly  can  be  seen  by

opening  the  cabinet  door  and  must  be  inspected  before

each  use of the grill. If the hose is damaged in any  way,

it  must  be  replaced  prior  to  using  the  grill  again.

Any  attempt  to  convert  the  grill  from  one  fuel  type  to

another  is  extremely  hazardous  and  will  void  the  war-

ranty.

Never  light  your  gas  grill  with  the  lid  closed  or  before

checking to ensure the burner tubes are fully seated over

the  gas  valve  orifices.

Never  allow  children  to  operate  your  grill.  Do  not  allow

children  or  pets  to  play  near  your  grill.  Always  supervise

children  and  pets  if  they  are  in  the  vicinity  of  the  unit.

Never 

use  charcoal  or  lighter  fluid  in  this  grill.

Use  of  alcohol,  prescription  or  non-prescription  drugs

can  impair  your  ability  to  properly  assemble  and

safely  operate  your  grill.

Keep  fire  extinguisher  readily  accessible.  In  the  event

of  a  oil/grease  fire,  do  not  attempt  to  extinguish  with

water.  Use  type  B  extinguisher  or  smother  with  dirt,

sand  or  baking  soda.
In  the  event  of  rain,  turn  off  the  burners  and  gas

supply.  Wait  for  the  grill  to  cool,  and  then  place  a

cover  on  it.
Use  your  grill  on  a  level,  stable  surface  in  an  area

clear  of  combustible  materials.

LP Gas grill models are designed for use with a standard

20  lb.  Liquid  Propane  Gas  (LP  Gas)  tank  (sold  sepa-

rately). 

Never 

connect  your  gas  grill  to  an  LP  Gas  tank

that  exceeds  this  capacity.  A  tank  of  approximately  12

inches in diameter by 18-1/2  inches high is the maximum

size LP  Gas tank to use. 

You must  use an 

"

OPD" gas

tank  which offers  a listed Overfill

 

Prevention  Device.

This  safety  feature  prevents  tank  from  being  overfilled

which  can  cause  a  malfunction  of  the  LP  Gas  tank.

Do  not  leave  grill  unattended  when  in  use.

Do  not  move  the  appliance  when  in  use.

Allow  the  grill  to  cool  before  moving  or  storing.

Do  not  use  your  grill  as  a  heater.

Never  use  your  gas  grill  on  a  balcony,  deck,  patio

above  the  ground  floor  of  your  home.
This  grill  is  not  intended  to  be  installed  in  or  on

recreational  vehicles  and/or  boats.

The  grill  is  not  intended  for  commercial  use.

!

  WARNING

!

Refer  to  the  this  table  when  designing  the  island  unit

for the BTH2616BLP & BTH3216BLP. Side* and Rear*

show  the  minimum  amount  of  distance  the  unit  must

be from combustibles (ex. Vinyl or wood siding, fences

and  overhangs)  or  sources  of  ignition  (ex.  Pilot  lights

on water heaters and live electrical appliances). Height*

shows  the  minimum  height  the  island  unit  must  be

starting  from  the  ground  up.

 

Side*

Depth

Height

Width

Non-combustible
Construction

Rear*

7"  minimum
clearance  from
cutout(for  lid)

Height*

Model

Height Width

Depth Side* Rear* Height*

BTH2616

BLP

9-1/2" 24-1/2" 19-3/4"

36"

36"

29"

BTH3216

BLP

9-1/2" 30-1/2" 19-3/4"

36"

36"

29"

!

Do  not  store  a  spare  LP-Gas  tank  under  or  near

this  appliance.
Never  fill  the  tank  beyond  80  percent  full;  and
If  the  information  in  "(a)"  and  "(b)"  is  not  followed

exactly,  a  fire  causing  death  or  serious  injury  may
occur.

A.

B.
C.

  WARNING

!

Summary of Contents for Turbo BTH2616ALP































Reviews: