background image

LED 1

LED 2

Gateway Status

 (flashing yellow)

Modbus Communication Active

 (flashing red)

Modbus Communication Error

For Gateway and Ethernet Bridge systems, active Modbus communication refers to the communication between the Gateway and the Ethernet Bridge. For GatewayPro
systems, the Modbus communication LEDs refer to the communication internal to the GatewayPro. For Gateway only systems, the Modbus communication LEDs refer to
the communication between the Gateway and its host system (if applicable).

Modbus Register Table

I/O

Modbus Holding Register

I/O Type

Units

I/O Range

Holding Register Rep-
resentation

Terminal

Block Labels

Gateway or

DX85

Any Node

Min. Value Max. Val-

ue

Min.
(Dec.)

Max.
(Dec.)

1

1

1 + (Node# × 16)

Discrete IN 1

-

0

1

0

1

DI1

2

2

2 + (Node# × 16)

Discrete IN 2

-

0

1

0

1

DI2

3

3

3 + (Node# × 16)

Discrete IN 3

-

0

1

0

1

DI3

4

4

4 + (Node# × 16)

Discrete IN 4

-

0

1

0

1

DI4

5

5

5 + (Node# × 16)

Analog IN 1

mA
V

0.0
0.0

20.0
10.0

0

65535

AI1

6

6

6 + (Node# × 16)

Analog IN 2

mA
V

0.0
0.0

20.0
10.0

0

65535

AI2

7

7

7 + (Node# × 16)

Reserved

8

8

8 + (Node# × 16)

Device Message

9

9

9 + (Node# × 16)

Discrete OUT 1

-

0

1

0

1

DO1

10

10

10 + (Node# × 16)

Discrete OUT 2

-

0

1

0

1

DO2

11

11

11 + (Node# × 16)

Discrete OUT 3

-

0

1

0

1

DO3

12

12

12 + (Node# × 16)

Discrete OUT 4

-

0

1

0

1

DO4

13

13

13 + (Node# × 16)

Analog OUT 1

mA

0.0

20.0

0

65535

AO1

14

14

14 + (Node# × 16)

Analog OUT 2

mA

0.0

20.0

0

65535

AO2

15

15

15 + (Node# × 16)

Control Message

16

16

16 + (Node# × 16)

Reserved

Specifications

Radio

General

Radio Range

900 MHz (1 Watt): Up to 9.6 kilometers (6 miles) *
2.4 GHz: Up to 3.2 kilometers (2 miles) *

Radio Transmit Power

900 MHz (1 Watt): 30 dBm conducted (up to 36 dBm EIRP)
2.4 GHz: 18 dBm conducted, less than or equal to 20 dBm EIRP

900 MHz Compliance (1 Watt Radios)

FCC ID UE3RM1809: This device complies with FCC Part 15, Subpart
C, 15.247
IC: 7044A-RM1809

2.4 GHz Compliance

FCC ID UE300DX80-2400 - This device complies with FCC Part 15,
Subpart C, 15.247
ETSI/EN: In accordance with EN 300 328: V1.7.1 (2006-05)
IC: 7044A-DX8024

Power*

Requirements: +10 to 30V dc (For European applications: +10 to 24V dc,
± 10%). (See UL section below for any applicable UL specifications)
900 MHz Consumption: Maximum current draw is <100 mA and typical
current draw is <50 mA at 24V dc. (2.4 GHz consumption is less.)

Housing

Polycarbonate housing and rotary dial cover; polyester labels; EDPM
rubber cover gasket; nitrile rubber, non-sulphur cured button covers
Weight: 0.26 kg (0.57 lbs)
Mounting: #10 or M5 (SS M5 hardware included)
Max. Tightening Torque: 0.56 N·m (5 lbf·in)

Antenna Connection

Ext. Reverse Polarity SMA, 50 Ohms
Max Tightening Torque: 0.45 N·m (4 lbf·in)

Interface

Indicators: Two bi-color LEDs

 

 

SureCross Performance Gateway

6

www.bannerengineering.com - tel: 763-544-3164

P/N 155861 Rev. D

Summary of Contents for DX80G9M6S-P2









Reviews: