B&R 5AP1120.0573-000, User Manual

Page: 179 / 204

International and national certifications
Automation Panel 1000 user's manual V2.00 179
Model number Description DNV GL
starting
with Rev.
5CASDL.0200-00 SDL cable - 20 m D0
5CASDL.0200-03 SDL flex cable - 20 m D0
5CASDL.0250-00 SDL cable - 25 m D0
5CASDL.0250-03 SDL flex cable - 25 m D0
5CASDL.0300-00 SDL cable - 30 m D0
5CASDL.0300-03 SDL flex cable - 30 m D0
5CASDL.0300-13 SDL flex cable with extender - 30 m D0
5CASDL.0400-13 SDL flex cable with extender - 40 m D0
5CASDL.0430-13 SDL flex cable with extender - 43 m D0
5CAUSB.0018-00 USB 2.0 connection cable - Type A - type B connector - 1.8 m D0
5CAUSB.0050-00 USB 2.0 connection cable - Type A - type B connector - 5 m D0
5DLSDL.1001-00 Automation Panel link module - SDL/DVI receiver - For Automation Panel 923/933/1000 E0
0TB103.9 Connector 24 VDC - 3-pin female - Screw clamp terminal block 3.31 mm² D0
0TB103.91 Connector 24 VDC - 3-pin female - Cage clamp terminal block 3.31 mm² D0
5AC804.MFLT-00 Line filter D0
For the DNV GL certificates with information about the permissible ambient conditions, see the B&R website Down-
loads - Certificates - Maritime - DNV GL .
Certificates for compass safe distance are available at Downloads - Certificates - Maritime - Compass safe distance .
10.2.6 UL Haz. Loc. certification
Ind. Cont. Eq.
for Haz. Locs.
Cl. I, Div. 2,
Groups ABCD
E180196 (T4)
Products with this mark are tested by Underwriters Laboratories and listed as "indus-
trial control equipment for use in hazardous locations". The mark is valid for the USA
and Canada and facilitates the certification of your machines and systems in this eco-
nomic area.
Underwriters Laboratories (UL) per standard ANSI/ISA 12.12.01
Canadian (CSA) standard per C22.2 no. 213-16
The UL HazLoc certificates are available on the B&R website under Downloads -
Certificates - HazLoc .
10.2.6.1 General safety guidelines
AP1000 panels with SDL or SDL3 link module that are certified for use in potentially explosive environments and
carry the marking above are suitable for use in Class 1, Division 2, Groups A, B, C and D or in nonexplosive
environments and correspond to the following standards: UL Std. 508 - 17th Edition, ANSI/ISA 12.12.01:2015,
CSA Std. C22.2 No. 213-16.
10.2.6.2 Assembly and installation
Explosion-protected devices must be used as intended and are only permitted to be operated by qualified and
instructed specialists in accordance with these installation instructions and the additional information in the user's
manual. Any other operation endangers the safety and function of the devices and connected systems. The oper-
ator is responsible for compliance with applicable safety and accident prevention regulations and standards.
Devices must be installed in a suitable protective housing that can only be opened using a tool. In order to en-
sure sufficient air circulation, the specified clearances must be observed. Use only in environments with pollution
degree 2. The maximum ambient temperature varies depending on the individual components used, see section
"Temperature specifications" on page 33 .
Before any installation or use of a device in potentially explosive atmospheres, the certification mark on the device
must be checked. Additional equipment must be suitable for the place of use. Final assembly must be approved
by the responsible local authorities. Wiring must be carried out in accordance with national regulations and the
requirements of the authorities.
Devices must be disconnected from the power supply until installation work has been completed. The tightening
torque for power supply terminals is 0.5 Nm. Cables must be suitable for a surface temperature of 75°C. AP1000
panels with SDL or SDL3 link module are only permitted to be operated with 24 VDC.