background image

Contact 

fl

 uid

Laboratory 

fl

 asks with 

sample 

fl

 uid

 roller carriage

1

2

3

18 / 25

51336-005 en/2022-03

1

 electronic GmbH & Co. KG  •  Heinrichstraße 3-4  •  12207 Berlin  •  Deutschland  •  [email protected]

4 Use 

 

The  shaking device is used together with the SONOREX DIGITEC DT 1028 F 

fl

 at 

 ultrasonic bath. Depending on the application, the shaking usually occurs indirectly in 
laboratory 

fl

 asks or other vessels, which are positioned in the 

 roller carriage.
Direct sonication of objects in the bath 

fl

 uid is not permitted in 

the DT...F ultrasonic baths and the  shaking device.

Notes on the use with the ultrasonic coupling

If inset beakers are used in the  ultrasonic bath, a contact 

fl

 uid 

must always be used as otherwise the ultrasound cannot pass 
through the air (between the ultrasonic oscillating tank and the inset beaker). This 
contact 

fl

 uid must be able to transfer the ultrasound to the 

fl

 uid in the inset beaker 

without loss if possible.
For more detailed information and instructions on correct ultrasound applications, 
please refer to the user instructions for the  ultrasonic bath.

4.1  

Preparing the  roller carriage for the application  

To avoid the 

fl

 asks' moving around or tipping over during operation of the  shaking 

device, BANDELIN recommends the use of special "EK"  holding clamps, see Section 7. 

The device must always be switched o

  before the  roller carriage is equipped with the 

 holding clamps. The  ultrasonic bath should also be switched o

  during the procedure. 

 Release the  coupling on the  roller carriage: Grasp the lever 1 behind the  bearing cup 

2 and pull it upwards. Leave or place the  clip bearing 3 back on the  ball stud. The 
 roller carriage can now be taken o

  the ultrasonic bath. 

 Equip the  roller carriage with the  holding clamps or replace the clamps if already 

mounted. 

 Position the  roller carriage back on the rim of the bath and check it for free 

movement.

 Press/click the  bearing cup 2 onto the lever 1 on the  ball stud (with  clip bearing 3). 

Summary of Contents for SONOSHAKE


























Reviews: