background image

Revision 3 May 2010

2.6 ATTACHING STOP

To attach metal stops to bottom rail of door. 

a)  Hook stop behind lip in rail, as shown. 

b)  Secure from underneath the rail with screws supplied. 

You will need to trim the weatherseal fl ush with the end 
of the bottom rail. 

 

ROLL-A-GUIDE

BOTTOM RAIL

BOTTOM RAIL LIP

STOP

2.5 TENSION THE SPRINGS

FIRST PREPARE A SOFT WOOD CHOCK, ABOUT 400mm LONG. 

 

 

 

THEN

 - Ensure that bottom rail is at the 3 o’clock position as shown in 

Step 4 - if not, refer to Step 2.4.

a)  Ensure both “U” bolts are tightened, then - 

 1. 

 

Rotate the door 1 1/2 turns in a forward direction to apply 
tension. Do not let go as the springs are now tensioned. See 
arrow in Fig (a). 

 2. 

 

Hold the door fi rmly, 

NOW

 cut the plastic wrap along the bottom 

rail  (taking care not to damage door surface or weatherseal). 

b)   Pull the curtain down slowly and carefully position the wooden 

chock (or other appropriate stop) as shown in Fig (b). Take care 
not to damage door surface. 

The chock will help hold the door until the guides and stops are fi tted. 

WOOD CHOCK

 

1

2

 

(a)

(b)

7

Roll-A-Door

®

 Series 1 Installation Instructions

Summary of Contents for Roll-A-Door Series 1













Reviews: