background image

 

1)

Forward Throttle Trigger

  Your Mad Shark can be driven forward by 

pulling the throttle trigger. Release the 
trigger and the Mad Shark will stop.

2) 

Left/Right Steering Wheel

  The steering wheel controls the Mad Shark ’s 

left and right movement. Turn the wheel to 
the left to steer to the left. Turn the wheel to 
the right to steer to the right. Release the wheel 
to go straight.

Racing Tip: The Mad Shark is an oval racer, 
designed for clockwise racing, and will be less 
responsive to steering inputs at high speed. 
Decrease your speed to allow tighter turning. 

1

2

4

NOTE:

If the Mad Shark begins to bob when running, it may have taken on an excessive amount of water. 
In this case, you should immediately return to shore, remove the upper deck and drain the water 
from the hull.

IF YOUR VESSEL DOES NOT OPERATE IN A STRAIGHT LINE 

If your Mad Shark do not run in a straight line 
when not being steered, you can adjust it by using 
the steering trim located on the upper right hand 
side of the transmitter.

1) Run your Mad Shark on calm water when 
     adjusting the steering. If your model runs to the 
     right when not being steered, press the
     “ST.TRIM-L” button. Re-center the model and see 
     if this has corrected the problem. Keep making 
     small adjustments in this way until the model 
     runs stright.

Press the “ST.TRIM-R” button to correct if your 
model steers to the left without being steered
in the same way as detailed above.

ST.TRIM-L

ST.TRIM-R

AFTER USE

1) When you have finished using your Mad Shark you should first switch ‘OFF’ the model (disconnect the 
     7.4V Power Pack), then switch ‘OFF’ your transmitter.  
2) Remove all batteries from the transmitter and model.
3) Leave ther Mad Shark’s upper deck off to allow moisture to evaporate. Ideally, place the model in this
     way in a warm and dry place, like an airing cupboard, until you are sure it is dry and then store it away. 
4) Remove the rubber ring from the slot of hull, so as to keep the rubber ring flexible for water proof 
     effective in next time boat racing.

 

 

Mad Shark V2 RTR MiNi EP F1 Speed Boat

HOW TO CONTROL/OPERATE YOUR MAD SHARK

Summary of Contents for MAD SHARK V2 RTR MINI EP F1 SPEED BOAT







Reviews: