Balmar Max Charge MC-624 Installation And Operation Manual Download

Page: 10 / 20

www.balmar.net / Customer Service: +1 (360) 435-6100 x1 / Technical Support: +1 (360) 435-6100 x3

Tech Service is available Monday - Friday (8:30am - 7:30pm EST)

Preset, Multi-Stage Battery Programs

Part Number:

Balmar Regulators

Digital

Duo

Charge

Dual

Engine

Centerfielder

12 Volt

24 Volt

ARS-5 MC-614 MC-612-DUAL MC-624 DDC-12/24 CFII-12/24

Universal Factory Program, Deep Cycle

Flooded, Gel Cell, Absorbed Glass Mat

(AGM) and Spiral Wound Flooded (Optima)

Yes

Standard Flooded, Halogen Systems, Lithium

Yes

Balmar Alternator Models
6-Series Alternators (70A-150A)

Yes

AT-Series Alternator (165A-200A)

Yes

9-Series Large Case Alternators (140A-310A)

Yes

Multiple Alternator/Engine Configurations
Dual Engine, One Alternator Each

Yes (qty 2)

Yes

Single Engine, Two Alternators

Yes

Yes (qty 2)

Yes

Ignition

Connector 1

Conne

ctor

External Regulator

Plug

Positive Battery Sense

(Required for Internal Regulator Only)

Isolated Ground Terminal

MUST be connected to system ground

Positive Output

Terminal

HOUSE BATTERY

BANK

D+

10A

Summary of Contents for Max Charge MC-624





















Search results

Summary of Contents for Max Charge MC-624

Reviews:

Related manuals for Max Charge MC-624

Brands by name

Popular brands

Balmar Max Charge MC-624, Installation And Operation Manual

Search results

Summary of Contents for Max Charge MC-624

Reviews:

Related manuals for Max Charge MC-624

Brands by name

Popular brands