389D001 Rev G
41 of 94
Press & Hold the Up arrow pushbutton until the “Setup” menu is displayed ~ 3 seconds
Set Point One Configuration:
- Press the Down arrow pushbutton to highlight [Set 1]
- Press the Right arrow pushbutton to access the Set 1 setting list
- Use the UP and Down arrow pushbuttons to highlight “db”
- Press & Hold the Right arrow pushbutton ~ 1 second then release to accept this setting
- Press the Down arrow pushbutton to highlight [1 act]
- Press the Right arrow pushbutton to access the 1 act setting list
- Use the Up and Down arrow pushbuttons to highlight “dir”.
- Press & Hold the Right arrow pushbutton ~ 1 second then release to accept this setting
- Press the Down arrow pushbutton to highlight [SP1 D]
- If this is not at ‘0’ press the Right arrow pushbutton to access the SP1 D setting list
- Set the delay to ‘0’ using Right and Left pushbuttons to select the digit and Up and Down pushbuttons
increase/decrease the value.
- Press & Hold the Right arrow pushbutton ~ 1 second then release to accept this setting
Set Point Two Configuration:
- Press the Down arrow pushbutton to highlight [Set 2]
- Press the Right arrow pushbutton to access the Set 2 setting list
- Use the UP and Down arrow pushbuttons to highlight “db”
- Press & Hold the Right arrow pushbutton ~ 1 second then release to accept this setting
- Press the Down arrow pushbutton to highlight [2 act]
- Press the Right arrow pushbutton to access the 2 act setting list
- Use the Up and Down arrow pushbuttons to highlight “rev”.
- Press & Hold the Right arrow pushbutton ~ 1 second then release to accept this setting
- Press the Down arrow pushbutton to highlight [SP2 D]
- If this is not at ‘0’ press the Right arrow pushbutton to access the SP2 D setting list
- Set the delay to ‘0’ using Right and Left pushbuttons to select the digit and Up and Down pushbuttons
to increase/decrease the value.
- Press & Hold the Right arrow pushbutton ~ 1 second then release to accept this setting
Set Point One Value and Deadband settings:
- Press & Hold the Up arrow pushbutton until the “Main” menu is displayed
- Press the Up and/or Down arrow pushbuttons to highlight “SP1”
- Press the Right arrow pushbutton to access SP1 value setting
- Use the Right and Left pushbuttons to select the digit and Up and Down pushbuttons increase/decrease the
value.
This is the “high” or “upper” setpoint. Set value to +0.10 above cabinet set point pressure
- Press & Hold the Right arrow pushbutton ~ 1 second then release to accept this setting
- Press the Down arrow pushbutton to highlight “SP 1 db
- Press the Right arrow pushbutton to access the SP1 db value setting
- Use the Right and Left pushbuttons to select the digit and Up and Down pushbuttons increase/decrease the
value.
This is the “high” or “upper” setpoint deadband. Set to 0.01
- Press & Hold the Right arrow pushbutton ~ 1 second then release to accept this setting
Summary of Contents for SterilGARD SG404
