background image

Step 30

Stake set down using 

Y41 stakes

 at locations shown using ¼” x 1” Phillips Truss Head Bolts, Flat Washers and ¼” 

Barrel Nuts. 

Measure in 6” from each end of Swing Beam Ground Board and screw stake into ground until 3” from top of Ground 
Board.  (You can use a screwdriver for leverage if needed)  Using hole in stake as guide drill through Ground Board 
with 3/8” drill bit.

Attach I.D. Plate to Swing Beam using #8 x ¾”  Wood Screws.

Attach Y10-16.5G Hand Grips to E1, E2 and E3 Tower Legs using 5/16” x 1-½” Bolts, Lock Washers and 5/16” 
Spike-T-Nuts.  Measure up 7” and 22” and center of M10 and drill through these locations with a 3/8” drill bit.

Attach Y10-16.5G to M10 using 5/16” x ½” Bolt, Lock Washer and 5/16” Spike-T-Nuts.   

ITEMS NEEDED

 

1-I.D. Plate
2-Y41 Ground Stakes
4-Y10-16.5G Hand Grips
  

HARDWARE NEEDED

2- ¼” x 1” Phillips Truss Head Bolts
2-1/4” Barrel Nuts
4-Flat Washers
2-5/16” Lock Washers
4-#8x3/4” Wood Screws
2-5/16” x ½” Bolts
6-5/16” x 1 ½” Bolts
12-5/16” Spike T Nuts
12-Lock Washers for Bolts

Metal Stake

FLAT

WASHER

BOLT

LOCK

WASHER

BO

ARD

FLAT

WASHER

BARREL

NUT

5/16"

PAGE 52

1 ” Truss

Head Bolts

G50

6”

6”

ID

Plate

M10

7”

22”

Summary of Contents for Patriot II

























































Reviews: