background image

STEP 29

Attach four (4) Swing Hangers to A1 Swing Beam with 3/8”x 5-3/4” Hex Bolts, 3/8” Lock Washers, 3/8” Flat Washers 

and 3/8” Spike T-Nuts

.  

Now attach Glider Supports to A1 Swing Beam using 5/16”x 5” WHA Bolts, Fender Washers, 

5/16” Lock Washers and 5/16” WHA Barrel Nuts. 

Attach A100004 Swing Beam Bracket to A1 with 5/16” x 4” Hex Bolts, Fender Washers and Lock Nuts. Attach A100005 

Triangle Brace to A1 using 5/16”x 4” Hex Bolts, Fender Washers and 5/16” Lock Nut

.

Attach E1 Angle Braces to SP 1 Beam Support with 3/8”x 6-1/2” Hex Bolt, 3/8” Lock Washer, 3/8” Flat Washer and 3/8” 

Spike T-Nut. (Note: Refer to Diagram for inserting spike T-Nut into counter-sunk hole).

Attach E2 Beam End Support to SP1 and E1 angle braces using 5/16”x 3” Lag Screws, 5/16” Lock Washers and Fender 

Washers to SP1 and 5/16”x 2-3/8” Lag Screws, 5/16” Lock Washers and Fender Washers to E1 Angle Braces.

Attach G1 Ground Board to E1 Angle Braces with 5/16”x 2” Lag Screws, 5/16” Lock Washers and Fender Washers.

Now attach Swing Beam Support assembly to Swing Beam using 5/16”x 4” Hex Bolts, Fender Washers and 5/16” Lock 

Nuts.

PAGE 48

A1

A100005

A100004

Use any convenient 

long 3/8" bolt.

ITEMS NEEDED

(1) A1 Swing Beam

(1) SP1 Beam Support

(1) E2 Beam End Support

(2) E1 Angle Braces

(1) G1 Ground Board

HARDWARE NEEDED

(2) Glider Supports (Y25G)

(2) Triangle Braces (A100005)

(2) L Braces (A100004) Swing Beam Mount

(4) Swing Hangers (Y40-HD4)

(6) 5/16” Lock Nuts

(6) 5/16” x 4” Hex Bolts

(8) 3/8” x 5 ¾” Hex Bolts

(9) 3/8” Flat Washer

(9) 3/8” Lock Washer

(9) 3/8” Spike Tee Nut

(2) 5/16” x 3” Lag Screw

(4) 5/16” x 2” Lag Screw

(4) 5/16” x 2 3/8” Lag Screw

(1) 3/8” x 6 1/2” Hex Bolt

(4) 5/16” x 5” WHA Bolt

(4) 5/16” WHA Barrel Nut

(24) Fender Washer

(20) 5/16” Lock Washer

5” WHA Bolt

Lock Washers 

& Fender Washers

Fender Washers

Barrel Nuts

WHA 

SP1

E1

E1

G1

E2

Summary of Contents for Highlander 6010





























































Reviews: