manualshive.com logo in svg

Avaya IP403 Office, Installation Manual, Page: 86 / 115

Share
Download
Avaya IP403 Office Installation Manual Download Page 86

IP Office Installation 

Installation Manual 

Page 80 

IP Office 2.1 

40DHB0002USCL Issue 10c (11th May 2004) 

ISDN Port – BRI (RJ45) 

Pin No.

 

Description

 

Signal Direction

 

3 

Transmit Data (Tx-A) 

> 

4 

Receive Data (Rx-A) 

< 

5 

Receive Data (Rx-B) 

< 

 

6 

Transmit Data (Tx-B) 

> 

 

ISDN Port – PRI (RJ45) 

Pin No.

 

Description

 

Signal Direction

 

1 

Receive Data (Rx-A) 

< 

2 

Receive Data (Rx-B) 

> 

4 

Transmit Data (Tx-A) 

> 

 

5 

Transmit Data (Tx-B) 

< 

 

LAN Port – 10/100 BaseT 

For IP Office 403/406 the information below refers to LAN ports 1 – 7. Port 8 is switchable (exchanges 
Tx and Rx signals). 

For IP412 and WAN3, both ports have the Rx and Tx connections exchanged. 

Pin No.

 

Description

 

Signal Direction

 

1 

Receive Data (Rx-A) 

< 

2 

Receive Data (Rx-B) 

> 

3 

Transmit Data (Tx-A) 

> 

   

6 

Transmit Data (Tx-B) 

< 

 

Summary of Contents for IP403 Office




















































































































Reviews:

No comments