manualshive.com logo in svg

Avaya IP403 Office, Installation Manual, Page: 19 / 115

Share
Download
Avaya IP403 Office Installation Manual Download Page 19

IP403 Office Platform 

Installation Manual 

Page 13 

IP Office 2.1 

40DHB0002USCL Issue 10c (11th May 2004) 

Typical Configuration 

Scenario 

A customer with sophisticated telephony requirements, needing 30 exchange lines and 80 Display 
Terminals. 

This configuration provides support for 98 Avaya 20 series digital telephones (18 spare for growth) and a 
single Primary Rate ISDN connection. If growth beyond 18 users or additional line capacity were 
anticipated, the IP406 Office would be considered more appropriate. Typically, a business of this size 
would have a data network built using LAN switches such as the Avaya Cajun range. The IP403 
Compact Office would be connected to the data network through its integral 8 port Hub, providing all 
users access to the Internet and IP Office productivity applications. 

 

Kit List 

• 

IP403 Office DT PRI 30 E1 

• 

3 x IP400 Digital Terminal Module 30 

• 

80 x 2030 Display Terminals 

 

 

 

  

Summary of Contents for IP403 Office




















































































































Reviews:

No comments