manualshive.com logo in svg

Avaya IP403 Office, Installation Manual, Page: 80 / 115

Share
Download
Avaya IP403 Office Installation Manual Download Page 80

IP Office Installation 

Installation Manual 

Page 74 

IP Office 2.1 

40DHB0002USCL Issue 10c (11th May 2004) 

Further Information and Product Updates 

Further Information and Product Updates 

Further information, including Product and Reference Manual updates, can be obtained from Avaya's 
Dealers and Distributors, or from Avaya's web site: http://www.avaya.com. 

This guide is also available from the Avaya's support web site: http://support.avaya.com  

 

Support Telephone Numbers 

For initial help and support, contact your distributor/supplier. The following contact points are for Avaya 
authorized partners. 

In the USA only

, Avaya provides a toll-tree Customer Helpline 24 hours a day: 

• 

Name: Avaya Technical Support Organization (TSO) 

• 

Customer Helpline: 1 800 628-2888 

• 

Address: 8744 Lucent Blvd., Highlands Ranch, Colorado, 80129 USA 

• 

URL: http://support.avaya.com/  

If you need assistance when installing, programming, or using your system, call the Helpline or your 
Avaya representative. Consultation charges may apply. 

 

Outside the USA

, if you need assistance when installing, programming, or using your system, contact 

your Avaya representative. 

• 

URL: http://support.avaya.com  

Summary of Contents for IP403 Office




















































































































Reviews:

No comments