manualshive.com logo in svg

Avaya IP403 Office, Installation Manual, Page: 67 / 115

Share
Download
Avaya IP403 Office Installation Manual Download Page 67

Basic System Programming 

Installation Manual 

Page 61 

IP Office 2.1 

40DHB0002USCL Issue 10c (11th May 2004) 

Software Upgrades 

Software Upgrades 

The software level of the IP Office Administration suite and the core software within the IP Office 
hardware should always be the same. Installing a new version of IP Office Manager includes core 
software files appropriate for upgrading the hardware. 

 

• 

Validated Upgrades

 

IP Office 2.1 software supports validated upgrades. This allows remote upgrades to be 
attempted. However validated upgrades are only supported for units with core software level 2.1 
or higher already installed.  

For hardware with Level 2.0 or earlier software installed, validated upgrades are not supported. 
Therefore, when upgrading a system to Level 2.1, the upgrade must be done from a PC running 
IP Office Manager that: 

• 

Has a fixed IP address.  

• 

Is connected on the same LAN segment as the IP Office control units.  

 

• 

Pre 2.0 IP403 Systems

 

These systems must follow a two-stage upgrade process. See 

Upgrading an IP403 to Software 

Level 2.

1

. 

 

Removing the Existing IP Office Admin Suite 

During this process, existing received configuration files are not affected.  

From 

Start

 select 

Settings | Control Panel | Add/Remove Programs.

 Highlight 

IP Office Admin 

Suite

 and click 

Change/Remove

.  

The Install Shield Wizard is run.  

Select 

Modify

 and click 

Next>

. 

Make a note of the ticked options. These indicate the components of the IP Office Administration 

suite current installed on the PC. Click 

< Back

.  

Select 

Remove 

and click 

Next

.

 

Confirm that you wish to remove all components.

 

 

If Read Only files are detected, click 

OK

. If Locked Files are detected, click 

Ignore

. 

Note:

 Your 

configuration and license files will be untouched and available for the upgraded software. 

Depending on the components removed you may be provided with the option to reboot your PC. 

Select 

Reboot. 

 

Click 

Finish

. 

You can now proceed with installing the new IP Office Admin suite, following the reboot if required.  

 

Summary of Contents for IP403 Office




















































































































Reviews:

No comments