manualshive.com logo in svg

Avaya IP403 Office, Installation Manual, Page: 109 / 115

Share
Download
Avaya IP403 Office Installation Manual Download Page 109

SNMP 

Installation Manual 

Page 103 

IP Office 2.1 

40DHB0002USCL Issue 10c (11th May 2004) 

Trap Generation 

RFC1215 Generic SNMP Traps:

 

Trap type

 

Generated

 

warmStart 

Upon soft reboot. 

coldStart 

Upon unexpected reboot such as a power outage. 

linkDown 

Upon transition of an interface (PPP or Frame-Relay) from the up 
operational state into the down operational state. 

linkUp 

Upon transition of an interface (PPP or Frame-Relay) from the down 
operational state into the up operational state. 

authenticationFailure 

Upon attempted SNMP request with mismatched community for the 
type of operation. 

IPO-MIB:

 

Trap type

 

Generated

 

ipoGenLKSCommsFailureEvent 

Upon loss of communication with a configured License Key 
Server. 

ipoGenLKSCommsOperationalEvent 

Upon re-gaining communication with a configured License 
Key Server. 

    

IPO-PHONES-MIB:

 

Trap type

 

Generated

 

ipoPhonesChangeEvent 

Upon change of a DT, DS or IP extension phone type after normal 
start-up. No traps are issued for POT extensions as the presence or 
absence of such phones cannot be established hence the 
ipoPhonesType for such extensions is always potPhone. 

 

Summary of Contents for IP403 Office




















































































































Reviews:

No comments