manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

Chapter 27: IPv6 traffic filter configuration

using the CLI

This chapter describes how to block unwanted traffic from entering a switch or to prioritize desired traffic.

Traffic filters instruct an interface to selectively handle specified traffic. The switch determines which

packets receive special handling based on information in the packet headers.

Using traffic filters, you can reduce network congestion and control access to network resources by

blocking, forwarding, or prioritizing specified traffic on an interface. You can apply multiple traffic filters

to a single interface.

For conceptual information about traffic filtering, see 

IPv6 routing fundamentals

 on page 17.

For additional information about filters, see 

Avaya Ethernet Routing Switch 8800/8600 Configuration —

QoS and IP Filtering for R and RS Modules, NN46205-507

 .

IPv6 traffic filter configuration navigation

•

Job aid: Roadmap of traffic filter CLI commands

 on page 321

•

Configuring ACTs

 on page 323

•

Creating a template for user-created patterns

 on page 325

•

Applying the ACT

 on page 327

•

Configuring ACLs

 on page 327

•

Configuring global and default actions for an ACL

 on page 328

•

Associating VLANs for an ACL

 on page 329

•

Associating ports for an ACL

 on page 330

•

Adding an ACE with IPv6 header attributes

 on page 331

Job aid: Roadmap of traffic filter CLI commands

The following table lists the commands and parameters that you use to perform the procedures
in this chapter.

Configuration — IPv6 Routing

November 2010     321

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

Sagem 2604 Quick Installation Manual preview
2604
Brand: Sagem Pages: 19
D-Link DI-634M Quick Installation Manual preview
DI-634M
Brand: D-Link Pages: 12
Eaton INDGW-X2 Manual preview
INDGW-X2
Brand: Eaton Pages: 10
MiLAN E-MCC-1600 Install Manual preview
E-MCC-1600
Brand: MiLAN Pages: 1
Symantec PacketShaper PS-S200 Quick Start Manual preview
PacketShaper PS-S200
Brand: Symantec Pages: 2
HMS Networks Anybus Communicator ABC4021 User Manual preview
Anybus Communicator ABC4021
Brand: HMS Networks Pages: 60
NETGEAR WGR614 - Wireless-G Router Wireless Reference Manual preview
WGR614 - Wireless-G Router Wireless
Brand: NETGEAR Pages: 116
Kohler Mira Pixel User Manual preview
Mira Pixel
Brand: Kohler Pages: 32
VoiceLine InnoMedia MTA 3328-2R Getting Started Manual preview
InnoMedia MTA 3328-2R
Brand: VoiceLine Pages: 18
Cradlepoint wipipe CTR350 Quick Start Manual preview
wipipe CTR350
Brand: Cradlepoint Pages: 2
Aerotech QNP3 Series Hardware Manual preview
QNP3 Series
Brand: Aerotech Pages: 62
TRENDnet TEG-S16R - DATA SHEETS Quick Installation Manual preview
TEG-S16R - DATA SHEETS
Brand: TRENDnet Pages: 12
RouterBOARD Groove A-52HPn Quick Setup Manual preview
Groove A-52HPn
Brand: RouterBOARD Pages: 4
Orcon Netcom NB6 Installation preview
Netcom NB6
Brand: Orcon Pages: 2
Paradyne FrameSaver SLV NNI Installation Instructions Manual preview
FrameSaver SLV NNI
Brand: Paradyne Pages: 20
TP-Link VN020-F2v Quick Installation Manual preview
VN020-F2v
Brand: TP-Link Pages: 2
Planet FGSW-4840S User Manual preview
FGSW-4840S
Brand: Planet Pages: 38
ADTRAN NetVanta 1224 Quick Start Manual preview
NetVanta 1224
Brand: ADTRAN Pages: 2

Brands by name

Popular brands

Load more brands