manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

Variable

Value

acl-id

Specifies an ACL ID in the range of 1–4096.

add 

<vid>

 [ 

<vid2-vid3>

]

Associates a VLAN or a VLAN list with a particular
ACL. 

<vid>

 is a list of VLANs separated by a comma

or a range of VLANs specified as low-high [vlan-id -
vlan-id].

info

Displays the ACL VLAN status.

remove 

<vid>

 [ 

<vid2-vid3>

 ]

Removes a VLAN or VLAN list from a particular ACL.

<vid>

 is a list of VLANs separated by a comma or a

range of VLANs specified as low-high [vlan-id -vlan-
id].

Associating ports for an ACL

Associate or remove ports for a particular ACL.

Procedure steps

Associate or remove ports by using the following command:

config filter acl

 

<acl-id>

 

port

Variable definitions

Use the data in the following table to use the 

config filter acl port

 command.

Variable

Value

acl-id

Specifies an ACL ID in the range 1–4096.

add 

<ports>

 ]

Associates a port or a port list with a particular ACL.

<ports>

 is a list of ports separated by a comma or a

range of ports specified as low-high [slot/port-slot/
port].

info

Displays the ACL port status.

remove 

<ports>

Removes a port or a port list from a particular ACL.

<ports>

 is a list of ports separated by a comma or a

range of ports specified as low-high [slot/port-slot/
port].

IPv6 traffic filter configuration using the CLI

330     Configuration — IPv6 Routing

November 2010

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

Panasonic BL-C20 Troubleshooting Manual preview
BL-C20
Brand: Panasonic Pages: 18
A-Link WNAP4G Quick Installaion Manual preview
WNAP4G
Brand: A-Link Pages: 6
ZyXEL Communications P-336M Specifications preview
P-336M
Brand: ZyXEL Communications Pages: 2
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Brand: IEI Technology Pages: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Brand: Dahua Technology Pages: 14
Brocade Communications Systems NetIron MLXe Series Hardware Installation Manual preview
NetIron MLXe Series
Brand: Brocade Communications Systems Pages: 305
Netis DL4305D Quick Installation Manual preview
DL4305D
Brand: Netis Pages: 16
WAGO 750-459 Manual preview
750-459
Brand: WAGO Pages: 48
Kohler Mira Pixel User Manual preview
Mira Pixel
Brand: Kohler Pages: 32
AOpen ISDN SOHO Router User Manual preview
ISDN SOHO Router
Brand: AOpen Pages: 89
Tenda DH301 User Manual preview
DH301
Brand: Tenda Pages: 120
Broadband Products Xtreme Networked Boat User Manual preview
Xtreme Networked Boat
Brand: Broadband Products Pages: 16
TRENDnet TEW-752DRU User Manual preview
TEW-752DRU
Brand: TRENDnet Pages: 68
XtendLan XL-VC102SB User Manual preview
XL-VC102SB
Brand: XtendLan Pages: 17
Xaptum ENF XAP-RW-001 Quick Start Manual preview
ENF XAP-RW-001
Brand: Xaptum Pages: 24
Watchguard Firebox T85-PoE Hardware Manual preview
Firebox T85-PoE
Brand: Watchguard Pages: 27
Digi TransPort WR54 Hardware Reference Manual preview
TransPort WR54
Brand: Digi Pages: 33
Honeywell CP-645 Installation Instructions Manual preview
CP-645
Brand: Honeywell Pages: 20

Brands by name

Popular brands

Load more brands