Avaya ERS 8600 series Configuration Manual Download

Page: 17 / 420

Chapter 3: IPv6 routing fundamentals

The router management features apply regardless of which routing protocols you use and include router

Internet Protocol version 6 (IPv6) configuration and IPv6 route table management.

Important:

IPv6 routing is not supported with Virtual Routing and Forwarding (VRF).

Navigation

•

The IPv6 header

on page 18

•

ICMPv6

on page 22

•

Neighbor discovery

on page 23

•

IPv6 and the Avaya Ethernet Routing Switch 8800/8600

on page 27

•

Management access

on page 28

•

Host autoconfiguration

on page 29

•

IPv6 VLANs and brouter ports

on page 30

•

Tunneling

on page 30

•

Path MTU discovery

on page 31

•

Routing

on page 31

•

OSPFv3

on page 47

•

Security

on page 51

•

Access policy extensions

on page 58

•

Multicast link discovery

on page 58

•

QoS and IPv6 filters

on page 59

•

•

•

•

Configuration — IPv6 Routing

November 2010 17

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Search results

Summary of Contents for ERS 8600 series

Reviews:

Related manuals for ERS 8600 series

Brands by name

Popular brands

Avaya ERS 8600 series, Configuration Manual

Search results

Summary of Contents for ERS 8600 series

Reviews:

Related manuals for ERS 8600 series

Brands by name

Popular brands