Autronica BX-10M1 Operator'S Handbook Manual Download Page 12

Page: 12 / 37

Operator's Handbook, Fire Alarm Control panel BX-10M1, P-BX10M1/FE Rev. A, 050128, Autronica Fire and Security AS

Page 10

3. LED indicators

3.1 Summary

The panel front comprises 24

LED indicators

. The individual

characteristics and response modes for these are given in subsequent
chapters concerning the various events/functions.

In addition, a detailed description of the indicator functions is provided in
the

Appendix

at the back of this manual.

The instant an alarm signal is activated, the LED indicators for FIRE
and FAULT will flash in time with the intermittent internal audio warning.

ALARM

Test

Fault

Disabled

Power

Zone 1

Zone 2

Zone 3

Zone 4

Alarms

Contr.

Al -outp.

Fault/Disabled/Test

Battery

Power

Earth

Fault

Zone 1

Zone 2

Zone 3

Zone 4

Fault outp.

Operator

Imm. alarm

Information

Alarm

System

Zone

Operator

Access code: xxx

Silence int. buzzer

Silence/res. alarms

Reset

Autronica Fire & Security

System

BX-10

Alarm call activated

Summary of Contents for BX-10M1






































Search results

Summary of Contents for BX-10M1

Reviews:

Related manuals for BX-10M1

Brands by name

Popular brands

Autronica BX-10M1, Operator'S Handbook Manual

Search results

Summary of Contents for BX-10M1

Reviews:

Related manuals for BX-10M1

Brands by name

Popular brands