Autronica BX-10M1 Operator'S Handbook Manual Download Page 32

Page: 32 / 37

Appendix

Operator's Handbook, Fire Alarm Control panel BX-10M1, P-BX10M1/FE Rev. A, 050128, Autronica Fire and Security AS

Page 30

BX-10M: Maritime version (P1BX10-116-xx).

This version is approved in accordance with the maritime
regulations, SOLAS. The version features the following:

•

Only for 230VAC.

•

Small cabinet.

•

Internal buzzer and alarm sounders (AK1 and AK2) are
activated with a fixed signal on alarm.

•

The delay for the alarm outputs is 2 minutes. The BMA
output has no delay.

•

A stropping between terminator 60 and 64 activates the
standard 2 minutes delay of alarm outputs.

•

No LED indication on front panel for delayed alarm
outputs.

•

Sounder alarm output signal, 7 short and 1 long, by
strapping between connection 5 and 6.

BX-10M1: Maritime version (P1BX10-116-xx).

This version is approved in accordance with the maritime
regulations, SOLAS and EN60945. The version features the
following:

•

Powered from 110-230VAC mains.

•

Double-sized cabinet.

•

Internal buzzer and alarm sounders (AK1 and AK2) are
activated with a fixed signal on alarm.

•

The delay for the alarm outputs is 2 minutes. The BMA
output has no delay.

•

A stropping between terminator 60 and 64 activates the
standard 2 minutes delay of alarm outputs.

•

No LED indication on front panel for delayed alarm
outputs.

•

Sounder alarm output signal, 7 short and 1 long, by
strapping between connection 5 and 6.

Summary of Contents for BX-10M1






































Search results

Summary of Contents for BX-10M1

Reviews:

Related manuals for BX-10M1

Brands by name

Popular brands

Autronica BX-10M1, Operator'S Handbook Manual

Search results

Summary of Contents for BX-10M1

Reviews:

Related manuals for BX-10M1

Brands by name

Popular brands