Automatic Heating AHG R32 AW Series Installation And Instruction Manual Download Page 19

Page: 19 / 22

Inverter Air Source Heat Pump (AHGR32AW17) - Installation and Instruction Manual

08. Appendix

8.1 Appendix 1 – Installation Schematic Diagram

8. Appendix

Key

Main Unit

Fan Coil

Rubber Flexible Connection

4 Thermometer
5 Manometer
6

Y-Type Filter

Ball Valve

10  Bypass Valve
11  Drain Valve
12 Filter
13  Two-Way Valve
14  Three-Way Valve

15  Automatic Ventilation
16  Water Pump
17  Ball Valve
18  Ball Valve
19  Expandable Water Tank
20  Automatic Fill-Water Valve

Notes:
1. The supplier only offers the main unit (1). The other parts, which are essential fittings, are

provided by the user or the installer.

2. This unit has an internal water pump and does not need an external water pump as shown

in diagram (16).

3. Automatic ventilation (15) is installed at the top point of the water system.
4. The quantity proportion of two-way valve (13) and three-way valve (14) shall be in

accordance with technical regulations, and there should be a three-way valve installed on
the farthest point of the water system.

5. The ball valve (17) is used when it is swashed or when the water system needs to be filled.

Summary of Contents for AHG R32 AW Series























Search results

Summary of Contents for AHG R32 AW Series

Reviews:

Related manuals for AHG R32 AW Series

Brands by name

Popular brands

Automatic Heating AHG R32 AW Series, Installation And Instruction Manual

Search results

Summary of Contents for AHG R32 AW Series

Reviews:

Related manuals for AHG R32 AW Series

Brands by name

Popular brands