background image

14

All key fobs saved in memory of the RAPTOR device 

will be deleted. The system will be in the mode of 

saving new key fobs.

4. 

For M52 key fobs (see marks on electronics board): 

 

Insert the battery into the new key fob. The LED on 

key fob will start flashing continuously with green 

light. It is recommended to put the key fob closer to 

the IGLA system during the procedure of connection. 

(The interaction radius during connection procedure 

is limited). After the successful connection the LED 

will  blink  once  with  red  light.  If  the  connection 

failed,  the  flashing  stops  in  30  seconds  after  the 

battery is inserted.

For  М24,  М51  key  fobs  (see  marks 

on electronics board): 

Close  the  key  fob  contacts  shown 

on the right drawing and insert the 

battery.  The  LED  indication  will 

start  flashing  green  every  second 

and when the key fob is connected 

it will flash red once.

5.  Switch OFF the ignition.

Be sure to check the key fob operation after connection 

it to the device.

ATTENTION! 

Save  both  key  fobs  into  the  system  at 

one time. It is impossible to add another key fob to an 

existing one later. Do not use the key fobs from another 

RAPTOR set.

ATTENTION! 

The old key fob (that was installed once 

before)  cannot  be  connected  to  the  device.  Use  only 

new key fobs bought from the manufacturer.

Summary of Contents for RAPTOR 151

























Reviews: