background image

 
 
 
 
 
 

CS-2205ADVTW1

 Deluxe 2-Way LED Paging Security System 

 
 

INSTALLATION & OPERATING INSTRUCTIONS 

 

 

CONGRATULATIONS

 on your choice of a Security System by Crimestopper Security Products Inc.  This booklet contains 

the  information  necessary  for  installing,  using,  and  maintaining  your  CS-2205  Advantage  alarm  system.    If  any  questions 
arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support number below. 

 

This  installation  book  is  designed  for  the  installer  or  individual  with  an  existing  understanding  of  automotive  electrical 
systems,  along  with  the  ability  to  test  and  connect  wires  for  proper  operation.   

To  ease  installation,  we  suggest  that  you 

READ  THIS  MANUAL  before  beginning  your  installation.    This  book  is  provided  as  a  GENERAL  GUIDLINE  and  the 
information contained herein may differ from your vehicle. 

 

*IMPORTANT INFORMATION: Primary and Optional Features

 

-PRIMARY:

  These are features that must be connected in order for the system to operate properly i.e. Siren, L.E.D., Power, 

Ground, Door Pin, and Flashing Lights etc. 

 

-OPTIONAL:

    These  are  features  are  to  be  connected  only  if  desired  or  agreed  upon  by  the  customer  and  the  installing 

dealer (i.e. Door Locks, Starter Disable, Hood/Trunk Protection and Auxiliary Remote Outputs etc.)  These features may also 
require additional parts and/or labor fees.  Consult with your installer beforehand to be sure of what is going to be installed 
with your particular system. 

 

TECH SUPPORT 
(800) 998-6880 
Hours: M-F 8:00AM-4:30PM 
 

     Pacific Std. Time 

REV B  6.2005 

This  device  complies  with  FCC  Rules  part  15.  Operation  is  subject  to  the  following  two 
conditions:  1)  This  device  may  not  cause  interference,  and  (2)  this  device  must  accept  any 
interference that may be received, including interference that may cause undesired operation.  
The manufacturer is not responsible for any radio or TV interference caused by unauthorized 
modification to this equipment. Such modification could void the user's authority to operate the 
equipment.

 

 

SERIES I 

Summary of Contents for CS-2205

































Reviews: