Austin Kontore Crestview Chicken Coop Assembly Manual Download Page 37 | Manualshive

Page: 37 / 54

background image

© 2009 Austin Kontore LLC

Page 37 of 54

Rotate the small level 90 degrees to verify that Door Slide
Rail is even and level with the top of the Lower Core
Square. Adjust the clamps as necessary.

The next steps will require drilling and fastening from the
inside of the unit. You can choose to go inside the coop, or
lean over and do the work from the outside.

From the inside of the coop, measure 7” from the outer
left edge and make a mark in the center of the Lower Core
Square.

Measure 7” from the outer right edge and make a mark in
the center of the Lower Core Square.

Measure 17” from the outer left edge and make a mark in
the center of the Lower Core Square.

There should now be three marks spaced out ready for
pre-drilling: A mark toward each end and one in the
middle.

«
...
35
36
37
38
39
...
»

Summary of Contents for Crestview Chicken Coop























































Reviews:

No comments

Related manuals for Crestview Chicken Coop

Brand: Backyard Play Systems Pages: 54

Brand: Gardena Pages: 19

Brand: Jackco Pages: 6

Brand: Tanaka Pages: 20

Brand: Tandem Pages: 80

Brand: Tanco Pages: 4

Brand: Ultrawave Pages: 30

Brand: Ultrasound Technologies Pages: 12

Brand: Zero 88 Pages: 12

Brand: Zest4Leisure Pages: 4

Brand: Zeiss Pages: 119

Brand: Zehnder Rittling Pages: 32

Brand: Posture Pump Pages: 2

Brand: Unika Pages: 8

Brand: ALL-FILL Pages: 32

ESK+ Manual Knee Lock

Brand: Blatchford Pages: 172

Brand: HEINE OPTOTECHNIK Pages: 52

Brand: Ugin Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands