Austin Kontore Crestview Chicken Coop Assembly Manual Download Page 3

Page: 3 / 54

Page 3 of 54

Required Tools

Electric or hand drill. A cordless power drill is preferred, but any kind
will work.

1/8” drill bit, for wood.

Power screw driver with Phillips bit or Phillips screw driver. A power
driver will make assembly much easier.

Post level (highly recommended). Makes alignment of posts
(uprights) much easier, since it uses bubbles in the key directions.
“Wraps around” the post and is held with a rubber band.

Small 6” to 18” level, though any level up to 28” will work.

Staple Gun. Either manual or electric, but electric will make screen
assembly easier.

Clamps. One-handed bar clamps (Irwin Quick Grip) are easy to work
with. Must have a 4” opening. (Standard 6” to 8” models are fine.)

Painting equipment (paintbrush, tray, rags, et cetera)

Summary of Contents for Crestview Chicken Coop























































Search results

Summary of Contents for Crestview Chicken Coop

Reviews:

Related manuals for Crestview Chicken Coop

Brands by name

Popular brands

Austin Kontore Crestview Chicken Coop, Assembly Manual

Search results

Summary of Contents for Crestview Chicken Coop

Reviews:

Related manuals for Crestview Chicken Coop

Brands by name

Popular brands