Audison bit One HD Virtuoso User Manual Download

Page: 31 / 90

USER'S MANUAL

Auto Input Switch

The automatic volume control for the

auxiliary source

(Aux - Optical 1/2)

can be activated through the Head Unit

volume control, if it is provided with an

AUX input

(see sec. 5.4.3, 5.6.1; 8.3.5).

If the car HEAD UNIT does not have

an AUX analog input, connect a USB

memory (or SD Card) to the USB reader

of your audio source as shown to the

side. The USB/SD device must contain

the mp3 format file available in the RVA

TONE folder located inside the Setup CD

(these files can also be downloaded from

the Audison website).

Please note that the storage device must

only contain this file and no other files.

If you use the USB memory to activate

the switching via the RVA function, simply select the USB (SD) or Master input.

Press

BACK

to go back to the previous step.

Press

NEXT

to continue with the configuration.

Press

SKIP

to bypass the procedure.

Follow the instructions listed below:

connect the

AUX IN

inputs of the

source (Head Unit) to the bit One HD

Virtuoso

RVA

input.

select the source AUX IN input

(Head Unit).

set the source volume to the maximum

undistorted level

At the end of the procedure:

Press

BACK

to go back to the

previous step.

Press

NEXT

to go ahead with the

configuration.

Press

CANCEL

to exit.

Summary of Contents for bit One HD Virtuoso



























































































Search results

Summary of Contents for bit One HD Virtuoso

Reviews:

Related manuals for bit One HD Virtuoso

Brands by name

Popular brands

Audison bit One HD Virtuoso, User Manual

Search results

Summary of Contents for bit One HD Virtuoso

Reviews:

Related manuals for bit One HD Virtuoso

Brands by name

Popular brands