Audi 2.7-litre V6 Biturbo Manual Download | Manualshive

Page: 40 / 72

background image

41

Functional positions of throttle valve control part (linear
representation)

The engine control unit recognises four key functional positions of the throttle valve control part.

•

The lower mechanical limit stop

The throttle valve is closed. This
position is required to adapt the angle
sender.

•

The lower electrical limit stop

is defined by the control unit and is
located just below the lower
mechanical limit stop. During
operation, the throttle valve closes no
further than the lower electrical limit
stop. This prevents the throttle valve
working its way into the throttle valve
housing.

•

The emergency running position

is the position of the throttle valve in
the deenergised state and ensures that
air flow is sufficient if any of the
relevant electronic accelerator functions
fails. Idling speed is higher - approx.
1000 rpm - and uneven.
Very limited vehicle operation is
possible.

SSP 198/21

SSP 198/22

SSP 198/24

Position of lower electrical limit stop

Emergency running position

Lower mechanical limit stop

«
...
38
39
40
41
42
...
»

Summary of Contents for 2.7-litre V6 Biturbo









































































Reviews:

No comments

Related manuals for 2.7-litre V6 Biturbo

Vickers M2-200 Series

Brand: Eaton Pages: 13

Brand: Yamaha Pages: 7

Brand: AL-KO Pages: 144

1550 STERNDRIVE

Brand: Mercury Racing Pages: 75

Brand: Brother Pages: 42

Brand: TIS Pages: 12

Brand: Slycma Pages: 34

Brand: Lycoming Pages: 83

Brand: Volvo Penta Pages: 90

Brand: Volvo Penta Pages: 108

Brand: Texas Equipment Pages: 38

Brand: Texas Equipment Pages: 57

Brand: Texas Equipment Pages: 60

Brand: Yanmar Pages: 35

Brand: Yanmar Pages: 164

Brand: Yanmar Pages: 65

Brand: Electro motive Pages: 287

Brand: PIREZ Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands