Audi 2.7-litre V6 Biturbo Manual Download

Page: 31 / 72

Actuators

Heater for lambda probe

(bank 1) Z19 and (bank 2) Z28

Divert air valve for turbochargers

Camshaft adjustment valve

(bank 1) N205 and (bank 2) N208

Throttle valve control part J338

with throttle valve drive G186

Solenoid valve for

charge pressure control N75

Solenoid valve for activated charcoal

canister N80

Output stage (bank 1) N122 and

ignition coils N (cyl. 1), N128 (cyl. 2)

and N158 (cyl. 3)

Injectors (bank 1) N30, N31, N32

Fuel pump relay J17 and

fuel pump G6

Output stage 2 (bank 2) N192 and

ignition coils N163 (cyl. 4), N164 (cyl. 5)

and N189 (cyl. 6)

Fault lamp for electric

throttle control K132

Auxiliary signals

Sensors

Engine speed sender G28

Hall senders (bank 2) G40 and (bank 1)

G163

Lambda probes (bank 1) G39 and (bank 2) G108

Throttle valve control part J338

with angle sender (1) G187 and (2) G188 for

throttle valve drive G186

Intake air temperature sender G42

Coolant temperature senders G2 and G62

Charge pressure sender G31

Knock sensors (bank 1) G61 and (bank 2) G66

Accelerator position sender G79 and 2 G185

Exhaust gas temperature senders (bank 1)

G235 and (bank 2) G236

Brake light switch F and brake pedal

switch F 47

Clutch pedal switch F36

Auxiliary signals

SSP 198/14

EPC

Injectors (bank 2) N33, N83, N84

Hot-film air mass meter G70

Control unit for Motronic J220

Altitude sender F96 is
integrated in the engine
control unit.

Diagnosis

Motronic ME 7.1

Summary of Contents for 2.7-litre V6 Biturbo









































































Search results

Summary of Contents for 2.7-litre V6 Biturbo

Reviews:

Related manuals for 2.7-litre V6 Biturbo

Brands by name

Popular brands

Audi 2.7-litre V6 Biturbo, Manual

Search results

Summary of Contents for 2.7-litre V6 Biturbo

Reviews:

Related manuals for 2.7-litre V6 Biturbo

Brands by name

Popular brands