Audi 2.7-litre V6 Biturbo Manual Download

Page: 24 / 72

SSP 198/31

Pneumatically controlled systems

In the Biturbo, 4 systems are pneumatically
controlled:

•

Charge pressure control

The Motronic ME 7.1 activates the solenoid
valve for charge pressure control N75 and
regulates the charge pressure via the
wastegate.

•

Divert air control in overrun

The Motronic ME 7.1 activates the electric
divert air valve for the turbocharger and
opens the pneumatic divert air valves using
this vacuum.

•

ACF system

The Motronic ME 7.1 activates the solenoid
valve for the activated charcoal canister
and regulates the fuel vapour feed rate to
the engine via the vacuum.

•

Crankcase breather

The crankcase breather controls the return
of oil vapours to the engine via two
mechanical valves.

Solenoid valve for charge
pressure control N75

Solenoid valve for activated
charcoal canister N80

Divert air valve for
turbocharger N249

Non- return valves (ACF system)

Distributor piece

Pressure control valve

Non-return valve (divert
air control in overrun)

Divert air valve
(pneumatic)

For exact the line routing, please refer
to the Workshop Manual.

Summary of Contents for 2.7-litre V6 Biturbo









































































Search results

Summary of Contents for 2.7-litre V6 Biturbo

Reviews:

Related manuals for 2.7-litre V6 Biturbo

Brands by name

Popular brands

Audi 2.7-litre V6 Biturbo, Manual

Search results

Summary of Contents for 2.7-litre V6 Biturbo

Reviews:

Related manuals for 2.7-litre V6 Biturbo

Brands by name

Popular brands