Audi 2.7-litre V6 Biturbo Manual Download | Manualshive

Page: 15 / 72

background image

16

Engine

The component parts of the oil circuit

is integrated in the primary flow. By increasing
the capacity and optimising the flow
resistance, the entire oil flow can be routed
through the oil cooler. Unlike the V6 naturally
aspirated engine, a bypass is not required.

The oil cooler ......

contains an oil retention valve, the filter
element, a bypass filter and the filter bypass
valve. The latter has the task of maintaining
engine lubrication via the bypass filter if the
filter element becomes clogged up or if the oil
has a high viscosity.

The oil filter ......

opens up the oil flow to the piston spray jets if
the oil pressure is greater than 1.8 bar.
Reason: at low oil viscosity and low engine
speeds, the oil pressure would otherwise drop
below the minimum permissible level. That
aside, piston cooling is not necessary at low
engine speeds.

The spray jets valve ......

SSP 198/57

Oil pressure control valve

Oil pressure limiting valve

Chain guard

is an internal gear pump. It is attached to the
crankcase as a separate component.

The oil pump is designed in such a way that it
projects deep down into the oil sump and is
immersed completely in the engine oil when
the oil level is correct. This prevents the oil
pump running dry.
The oil pump, in combination with the
extremely short intake path, enables oil
pressure to build up more quickly and safely,
particularly during cold starts.
The oil pump is driven by the crankshaft by
means of a single chain.
A spring-loaded flat plate produces the
necessary tension.

A new feature of the oil pump is the chain
guard made from sheet steel. It encapsulates
both the chain wheel and the chain over a large
area.
This reliably prevents oil frothing and the
problems associated with this.

The oil pump ......

«
...
13
14
15
16
17
...
»

Summary of Contents for 2.7-litre V6 Biturbo









































































Reviews:

No comments

Related manuals for 2.7-litre V6 Biturbo

Brand: pumpa Pages: 32

Brand: ALL POWER AMERICA Pages: 28

Brand: Team Orion Pages: 2

Brand: Chicago Electric Pages: 8

Brand: Leadshine Technology Pages: 55

Brand: Texas Equipment Pages: 25

Brand: Fagor Pages: 86

Brand: V.P.S. Pages: 25

Brand: Honda Pages: 5

Brand: Honda Pages: 16

SATURNO BIALBERO 350

Brand: Gilera Pages: 140

Brand: Wood-mizer Pages: 24

Brand: Paccar Pages: 92

Brand: JAC Pages: 14

Brand: Yanmar Pages: 112

Brand: SKY Engines Pages: 49

Cobra 4.6L (4V)

Brand: Ford Pages: 15

Brand: YARDMAX Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands