Audi 2.7-litre V6 Biturbo Manual Download | Manualshive

Page: 39 / 72

background image

40

SSP 198/28

Subsystems of the Motronic

The throttle valve control part comprises...

... throttle valve housing with throttle valve
... throttle valve drive G186 with reduction
gear
... angle senders for throttle valve drive
G187 and G188

Activated by the engine control unit, the
throttle valve drive controls the air-flow rate
necessary to develop the required torque.
Feedback on momentary throttle valve
position is provided by two potentiometers
G187 and G188.

For safety reasons, two angle senders
(redundancy) are used. They have opposite
impedance characteristics (see diagram).

If an angle sender fails, the second sender
maintains the electronic accelerator function
via an emergency running program.

Throttle valve housing
with throttle valve

Housing cover with electrical
connections

Throttle valve drive G186
(Electric throttle control)

Angle senders for throttle valve
drive G187 and G188

Resistance in

Ω

Angle senders G187 and G188 cannot
be replaced separately. The throttle
valve control part may not be opened.

Redundancy means: superfluous,
non-essential.

0

100%

SSP 198/27

G188

G187

Throttle valve opening in %

throttle valve control part J338 with throttle valve drive G186, angle
senders 1 G187 and 2 G188 for throttle valve drive

«
...
37
38
39
40
41
...
»

Summary of Contents for 2.7-litre V6 Biturbo









































































Reviews:

No comments

Related manuals for 2.7-litre V6 Biturbo

Brand: J.A.P Pages: 21

MICROPUMP DEELE

Brand: Idex Pages: 23

Brand: RHINO MOTION CONTROLS Pages: 4

Vanguard EFI 380000

Brand: Briggs & Stratton Pages: 100

Brand: Parker Pages: 32

Brand: Marcato Pages: 42

Brand: Honda Pages: 40

Brand: Honda Pages: 42

Brand: Honda Pages: 48

Brand: Honda Pages: 80

Brand: Volvo Penta Pages: 122

Brand: ST Pages: 251

Brand: Kyosho Pages: 4

Brand: Hirth Pages: 21

Brand: 3W Pages: 19

Brand: Oemer Pages: 97

Brand: Vanguard Pages: 104

Brand: GAOKIN Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands