Au Group Electronics
Au SAE J1939 Simulator (Gen II) 2.00A User Manual Rev. D
4
The part # for 6 editions of Au SAE J1939 simulator Gen II 2.00A and required accessories are listed in Table 1-1
Table 1-1Part # for Au SAE J1939 simulator
(Gen II) 2.00A
and necessary accessories
Au SAE J1939 Simulator (Gen II) 2.00A, Accessories, and Service
Part #
Au J1939 Simulator (Gen II 2.00A)
Engine Basic
Edition
SIMJ1939-007
Au J1939 Simulator (Gen II 2.00A)
Engine Premium
Edition
SIMJ1939-008
Non-Plus Edition
Au J1939 Simulator (Gen II 2.00A)
Vehicle Platinum
Edition
SIMJ1939-009
Au J1939 Simulator (Gen II 2.00A)
Engine Basic
Plus
Edition
SIMJ1939-010
Au J1939 Simulator (Gen II 2.00A)
Engine Premium
Plus
Edition
SIMJ1939-011
Plus Edition
Au J1939 Simulator (Gen II 2.00A)
Vehicle Platinum
Plus
Edition
SIMJ1939-012
RS232 Serial Extension Cable
CBL-RS232-01
4-wire cable for power supply and CAN network connection
CBL-CAN-01
Accessories
USB to RS232 Serial Adapter
ADP-USB-232
Service
1 year support and minor upgrades for Au J1939 Simulator
SVS-SIM-J1939
1.3. Major Hardware Features
Major hardware features of Au
SAE J1939 Simulator (Gen II) 2.00A are listed below:
•
SAE J1939-15 Type II ECU:
contains an internal 120 ohm load resistor for easy network setup
•
Common-Mode Choke and TVS (Transient Voltage Suppressor)
protection on CAN bus
•
Compact size:
4-1/8" L X 1-3/4"W X 7/8”H
•
Enclosure color
: Black or PC white
•
Operating temperature:
-4
˚
F to 185
˚
F (-20
˚
C to 85
˚
C)
•
Power supply:
+12V~+24V DC, 250mA max
•
9 LED indicators:
Power, Range, Warning,
▼
0%, 20%, 40%, 60%, 80%,
▲
100%
•
1 buzzer
•
3 push buttons:
The SAE J1939 simulated signal can be adjusted by push buttons: Menu, Down, Up
•
1 DB9 Male "BUS" Interface
(Figure 1-2)
:
A four-wire cable (Au Part#: CBL-CAN-01, order separately) can be used for power supply and SAE J1939 network
connection. One end of the cable "CBL-CAN-01" is a DB9 connector which will mate with the “BUS” connector on the
simulator. The other end of the cable consists of pigtail wires which can connect power supply and CAN network. The
color definition of each wire of the cable is illustrated in Table 1-2.
Table 1-2
Color definition of the 4-wire cable (CBL-CAN-01, order separately)
Color
Signal
Red
+12 V power supply
White
CAN-H
Green
CAN-L
Black
Ground
•
1 RS232 interface:
It is used
for in field firmware update, license management and computer remote control (
Plus
editions only). Au J1939
Simulator
Plus
editions can be connected to the RS232 (serial) port of a PC, either through a RS232 serial extension
cable (Part#: CBL-RS232-01, order separately), as shown in Figure 1-4; or through a USB to RS232 serial Adapter with
USB extension cable (Part #: ADP-USB-232), as shown in figure 1-5. Please refer chapter 4 for detail information on
Remote Terminal Program.
