ATTACK ATTACK DPX 25 COMBI Pellet Instructions For Use Manual Download Page 46

Page: 46 / 100

The paper box ought contain the following items:

•

1 pc. ATTACK PELLET BURNER Automatic 15 – 50 kW

•

1 pc. plug of upper loading chamber

•

1 pc. inlet tube with emergency thermostat of back–burning

•

1 pc. fireproof concrete roof

•

1 pc. pantograph

•

1 pc. burner door

Note

: Boiler temperature sensor for burner has been by factory installed in the boiler. This sensor needs

to be connected to the connector of burner electronics, signed TS2, after burner installation.

9.3

BURNERS DIMENSIONS

ATTACK PELLET BURNER Automatic 8 – 30 kW

ATTACK PELLET BURNER Automatic 15 – 50 kW

Summary of Contents for ATTACK DPX 25 COMBI Pellet





































































































Search results

Summary of Contents for ATTACK DPX 25 COMBI Pellet

Reviews:

Related manuals for ATTACK DPX 25 COMBI Pellet

Brands by name

Popular brands

ATTACK ATTACK DPX 25 COMBI Pellet, Instructions For Use Manual

Search results

Summary of Contents for ATTACK DPX 25 COMBI Pellet

Reviews:

Related manuals for ATTACK DPX 25 COMBI Pellet

Brands by name

Popular brands