Atmos A85 Operation And Maintenance Manual Download

Page: 9 / 66

Operation and Maintenance Manual - EN

www.atmos.cz

EN-9

3. Burner accessories

Accessory - burner part

Stop for the end switch

1 piece

Interconnection cable between the boiler and the burner with a connector (6x1.5 mm)

1 piece

Operation and Maintenance Manual

1 piece

Fuse - type F 3.15A/1500A/5x20mm (ignition spirals)

2 pieces

Fuse - type F 0.8A/1500A/5x20mm (conveyor)

1 piece

Fuse - type F 1.0A/1500A/5x20mm (ventilator)

1 piece

Poker for cleaning – small

1 piece

CP85KS set for the A85 burner with a compressor

1 piece

Accessories that are not part of the burner and can be purchased separately:

DRA50 pellet conveyor with the length of 1,7 m and diameter of 80 mm - 25 W - CODE: H0039

DRA50 pellet conveyor with the length of 2,5 m and diameter of 80 mm - 25 W - CODE: H0037

DRA50 pellet conveyor with the length of 4 m and diameter of 80 mm - 40 W

- CODE: H0004

DRA50 pellet conveyor with the length of 5 m and diameter of 80 mm - 40 W

- CODE: H0005

Water temperature sensor

with a 5 m cable (range - 20 ...+ 110 °C)

type

KTF

CODE:

P0431

Flue gas temperature sensor

with a 2.5 m cable (range -20 ...+ 300 °C)

type

VFF00-75P65

CODE:

P0414

Pocket

for a flue gas sensor to be positioned in the flue gas duct, G1/2“ x 85 mm - CODE: V0524

Cavity

with tin for extension of conductors (sensors)

- CODE: P0445

Summary of Contents for A85



































































Search results

Summary of Contents for A85

Reviews:

Related manuals for A85

Brands by name

Popular brands

Atmos A85, Operation And Maintenance Manual

Search results

Summary of Contents for A85

Reviews:

Related manuals for A85

Brands by name

Popular brands