Atmos A85 Operation And Maintenance Manual Download Page 50

Page: 50 / 66

www.atmos.cz

50-EN

Operation and Maintenance Manual - EN

• Fan speed -

displays the

current speed of the fan

• Fan speed 2 –

displays the

current speed of fan 2 (not used)

• Conveyor -

displays the

current status of the conveyor

• Conveyor faults -

displays

information for the service engineer

• Spirals -

displays

the current status of the ignition spirals

• Spiral faults -

displays

information for the service engineer

• Reserve R -

displays the

current status of the reserve output R (parameter S6)

• Reserve R2 -

displays the

current status of the reserve output R2 (parameter S14)

• Reserve R5 -

displays the

current status of the reserve output R5 (parameter S67)

• Reserve R6 -

displays the

current status of the reserve output R6 (parameter S68)

TESTING menu

• Autotest

– This function is used for automatic testing of all the basic elements of the burner as the

fan, conveyor, ignition spirals, etc. The testing is carried out consecutively in 20-second intervals

so that the engineer can monitor the operation of individual devices.

If this test is not sufficient, individual devices can be run separately, namely with the use of the

following functions.

CAUTION

– During testing the burner is put out of operation, therefore before the start of

testing always let the burner properly burn out

with the use the STOP command.

• Fan

- this function is used to test the operation of the fan

• Conveyor

- this function is used to test the operation of the conveyor

• Spiral 1

- this function is used to test the operation of the ignition spiral 1

• Spiral 2

- this function is used to test the operation of the ignition spiral 2

• Reserve R

– this function is used to test the switching device (relay) of the reserve output R

• Reserve R2

– this function is used to test the switching device (relay) of the reserve output R2

• Reserve R5

– this function is used to test the switching device (relay) of the reserve output R5

• Reserve R6

– this function is used to test the switching device (relay) of the reserve output R6

• Photocell

- used to test the photocell. Conduct the test by observing its sensitivity when it is

inserted in the burner or outside the burner in the natural light (never on the sun – will cause an alarm).

Summary of Contents for A85



































































Search results

Summary of Contents for A85

Reviews:

Atmos A85, Operation And Maintenance Manual, Page: 50 / 66

Search results

Summary of Contents for A85

Reviews: