background image

ATIM_ACW-DINDIO_868_UG_EN_V1.3 

 

General hazard 

 Failure to follow the instructions presents a risk of equipment damage. 

 

Electrical hazard 

 Failure to follow the instructions presents a risk of electrocution and physical 

injury. 

 

Direct-current symbol 

 

 

WARNING: do not install this equipment near any source of heat or any source of humidity. 

 

 

WARNING: for your safety, it is essential that this equipment be switched off and disconnected from mains 
power before carrying out any technical operation on it. 

  

 

WARNING: the safe operation of this product is ensured only when it is operated in accordance with its 
intended use. Maintenance may only be performed by qualified personnel. 

 

Waste  disposal  by  users  in  private  households  within  the  European  Union.  This  symbol  appears  on  a 
product or its packaging to indicate that the product may not be discarded with another household waste. 
Rather, it is your responsibility to dispose of this product by bringing it to a designated collection point for 
the recycling of electrical and electronic devices. Collection and recycling waste separately at the time you 
dispose of it helps to conserve natural resources and ensure a recycling process that respects human health 
and the environment. For  more  information on the  recycling centre closest  to your home, contact your 
closest  local  government  office,  your  local  waste  management  service  or  the  business  from  which  you 
purchased the product. 

 

Radio 

Modems in the ACW line are radio-communication modems that use the ISM (industrial, scientific and 
medical) bands, which may be used freely (at no cost and with no authorisation required) for industrial, 
scientific and medical applications. 
 
 

 

Summary of Contents for Cloud Wireless ACW/868-DINDIO



















Reviews: