17
parts must be correctly installed and fulfil all conditions
to ensure perfect operation of the saw
−
Damaged guards
and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
−
Damaged or illegible
safety warning labels
should be
replaced
immediately.
Do not allow any tool key to be plugged in!
Store the
unused machine
in a dry locked place away from
the reach of children.
Electrical safety
Design of the
connection cable
according to IEC 60 245
(H 07 RN-F) with a core cross-profile section of at least
1.5 mm
2
for cable lengths
up to
25 m
2.5 mm
2
for cable lengths
over
25 m
Long and thin connection lines result in a potential drop.
The motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs
and
coupler outlets
on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
The connector of the connection cable must be
splash-
proof
.
When running the
connection line
observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Do not use the
cable
for purposes for which it is not meant.
Protect
the cable against
heat, oil and sharp edges
. Do
not use the cable to pull the plug from the socket.
Wind off completely the cable when using a cable drum.
Regularly check the
extension cables
and replace them if
they are damaged.
Do
not use any defective connection cables.
When working outdoors, only use extension cables
especially
approved
and appropriately labelled for outdoor
use.
Do
not set up any provisional
electrical connections.
Never bypass
protective devices or deactivate them.
The device must be connected via the fitted PRCD
(residual-current-operated circuit breaker).
The
electrical connection
or
repairs
to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs
to other parts of the machine must be carried out
by the
manufacturer
or one of his customer service
points.
Use only original
spare. Accidents can arise for the user
through the
use of other spare parts
. The manufacturer
is not liable for any damage or injury resulting from such
action.
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
o
o
f
f
d
d
e
e
v
v
i
i
c
c
e
e
/
/
s
s
p
p
a
a
r
r
e
e
p
p
a
a
r
r
t
t
s
s
Pos. Denomination
Order-No.
1.
Rear frame section
364042
2.
Front frame section
364043
3.
Frame 364044
4. Support
brace
364045
5. Lateral
support
364046
6.
Locking nut for mitre cut
364047
7.
Scale for mitre cut
364048
8. Trough
364049
9.
Table plate (3 pieces)
364050
10.
Stopper bar (2 pieces) with scale
364051
11.
Angle fence
364052
12.
Star handled nut M6 for angle
adjustment
364053
13. Guide
bar
364054
14. Cutting
unit
364055
15.
On-off switch
364056
16. Handhold
364057
17 Splash
guard
364058
18. Hose
364059
19.
Covering cap
364060
20.
Cutting-off wheel Ø 200 x Ø 25,4 x 2,2
mm
364067
21.
Installation wrench
364040
22.
Socket wrench SW 30
364039
23.
PRCD (residual-current-operated circuit
breaker)
364041
24. Cooling
water
pump
364061
25. Safety
label
364010
26.
Machine knob nut M6
364053
27. Motor
safety
pin
364063
28.
Transport screw for cutting unit
364064
29.
Holding eyelet for cooling water hose
364065
30.
Hexagon screw M6 x 18
364066
31. Front
flange
364038
32. Rear
flange
364070
33.
Hexagon nut M 16 LH
364071
34. Closing
plug
364072
35.
Fan (not illustrated)
364074
36.
Fan cooling (not illustrated)
364075
37. Capacitor (not illustrated)
364073
38.
Hose clamp (not illustrated)
364062
