ATIKA BF 31-4T, Original Instructions Manual

Page: 23 / 216

23
perfectly and with their intended function. Only operate the
machine with complete and correctly attached safety
equipment and do not alter anything on the machine that
could impair the safety.
−
Check whether the movable parts function perfectly and
do not stick or whether the parts are damaged. All parts
must be correctly installed and fulfil all conditions to
ensure perfect operation.
−
Damaged guards and parts must be properly repaired or
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
−
Damaged or illegible security labels have to be replaced.
• Do not allow any tool key to be plugged in!
Before switching on, check always that all tools are removed.
•
Store unused equipment in a dry, locked place out of the
reach of children.
•
Note that a failure to maintain the unit properly, any use of
non-conform spare parts or a removal / modification of safety
devices can result in damages to the machine and to serious
injuries of the person who works with it.
Do not carry out repair operations on the machine other
than those described in section "Maintenance and care"
but contact the manufacturer or authorized customer
service centre.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not liable
for any damage or injury resulting from such action.
Behaviour in an emergency situation

Initiate all required first aid measures suited for the injury
and seek qualified medical advice as quickly as possible.

Protect the injured person against further injuries and
immobilise the injured person.
Safety instructions - Safe handling of fuels
Fuels and fuel vapours are inflammable and may
cause serious injury on the skin or when inhaled.
Therefore be careful and provide sufficient
ventilation when handling with fuels.
•
Do not smoke and avoid open flames when fuelling.
•
Wear gloves when fuelling.
• Do not fuel in closed rooms.
• Stop the device and allow it to cool down.
•
Carefully close the tank cap after fuelling and check that it
does not get loose during operation.
•
Avoid spilling of fuel or oil. Clean the device immediately
when you have spilled fuel or oil. Change your clothes
immediately when you have spilled fuel or oil on them.
•

Make sure that no fuel can enter the soil.
•
Check that there is no leakage on the tank cap and fuel lines.
If there are leaks this product may not be started.
•
Never use a device with damaged ignition cable and spark
plug connector. Risk of sparking.
•
Only transport and store fuels in containers approved and
identified for this.
• Keep children away from fuels.
•
Do not handle and store fuels close to combustible and
highly inflammable materials as well as sparks and open
flames.
•
Go away at least three meters from the fuelling place to start
the device.
Description of device

Please refer to the attached assembly and operating
instruction sheet.
Pos. Denomination Order-No
1 Drive unit
2 Lower tube shaft with angular gear 385857
3 Handle with safety switch
3a Gas cable
4 Double shoulder carrying strap 385853
4a Suspension eye
4b Snap hook for the carrying strap 385842
5 Safety guard 385866
5a Dirt catcher
6 Thread spool 385854
6a Spool cover (2-pieces) 385892
6b Thread spool roll 385869
6c Compression spring 385839
7 Cutting blade 385855
7a Transport guard for cutting blade
8 Safety guard holder
9 Angular gear
10 Thread knife 385867
10a Transport guard for thread knife
11 Safety guard holder
12 Throttle lever lock
13 ON/OFF switch
14 Cold start switch
15 Throttle lever
16 Air filter cover
17 Spark plug connector
18 Silencer
19 Fuel tank
20 Cranking handle
21 Oil filling plug 385884
22 Tank cap 385876
23 Choke lever
24 Priming pump
25 Wing screw
26 Button cover
27 Holding plate
28 Hexagon nut 385859
29 Cover 385862
30 Spacer washer 385861
31 Air filter 385878
32 Fuel filter 385895
33 Spark plug 385888
34 Fuel tank
35 Allen key, size 4
36 Allen key, size 5
37 Open-end wrench, size 8/10
38 Socket wrench