14
When working on slopes always make sure to have a safe
standing position.
Only move the machine at walking speed, never run with it
(changing locations).
Be observant. Attend to what you do. Start working with
rationality. Do not use the device when you are tired or
under the influence of drugs, alcohol or medicaments. One
moment of carelessness when using the device can result in
serious injuries.
Always wear safety goggles, work gloves and noise
protection when working with the machine.
Always wear suitable work clothing when operating the
machine:
−
do not wear loose-fitting clothes or jewellery; they can
catch in moving parts.
−
slip-proof shoes
−
Trousers to protect the legs
−
no loose clothing or such with hanging bands or
drawstrings
Do not work with the device barfooted or only with thongs on
your feet.
Within his area of work the operator is responsible for third
parties.
Do not allow children to play with this machine.
Keep children away form machine.
Do not allow children to perform cleaning and maintenance
tasks.
Never operate the machine if other persons, especially
children, or animals are in the immediate vicinity.
The operator is responsible for accidents or hazards which
occur to other persons or their properties.
Never leave the device unattended.
Keep your workplace in an orderly condition! Untidiness can
result in accidents.
Choose a working position alongside the equipment or
behind it. Never stand near the ejection opening.
Never reach into the filling or ejection opening.
Keep your face and body away from the filling opening.
Do not overload the machine! You work better and safer in
the given performance range.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on the
machine that could impair the safety.
Never try to bypass the interlocking function of the safety
device.
Do not alter the motor controller setting, since the rotary
speed controls the safe maximum operating speed, and
protects the motor and all rotating parts against damage due
to excess speed. Contact the customer service in case of
problems.
Do not operate without the funnel.
Close machine properly before enabling motor.
Do not modify the device or parts of the device respectively.
Do not hose down the device with water. (Origin of danger
electric current).
Take into consideration environmental influences:
−
Do not use the device in moist or wet ambience.
−
Do not leave the machine standing in the rain.
−
Do not work in bad weather conditions (e.g. rain, risk of
lightning).
−
Provide for good illumination.
To prevent danger of injury to fingers during assembly or
cleaning operations wear protecting gloves.
Do not transport the device when the motor is running.
Switch off the machine and pull the mains
plug from the socket and make sure that
all moving parts have come to a complete
standstill before:
−
attaching or removing the collecting bag
−
performing maintenance and cleaning work
−
eliminating faults
−
checking the connection cable for damage and
entanglement during operation
−
transporting
−
carrying out repair work
−
leaving unattended (even during short interruptions)
If the machine’s filling funnel or ejection slot is blocked
switch off the motor and disconnect the mains plug before
removing material from the filling funnel or ejection slot.
Do not touch dangerous moving parts before the machine
has been isolated from the electric supply and such moving
parts have come to a dead stop.
The power or extension cable must be separated from the
supply mains immediately if they are damaged during use.
Do not touch the cable before it is disconnected from mains.
Do not use the machine if the cable is damaged or worn.
Check the machine for possible damage:
−
Before further use of the machine the safety devices
must be checked carefully for their proper and intended
function.
−
Check whether movable parts function perfectly and do
not stick or whether parts are damaged. All parts must
be correctly installed and fulfil all conditions to ensure
perfect operation of the machine.
−
Damaged safety devices and parts must be properly
repaired or exchanged by a recognized, specialist
workshop; insofar as nothing else is stated in the
instructions for use.
−
Damaged or illegible safety labels have to be replaced.
Store unused equipment in a dry, locked place out of the
reach of children.
Store the machine in a place where fuel vapours cannot
come close to open flames or sparks. Always allow the
machine to cool down before storing it.
Maintain the machine with care and keep it clean.
Electrical safety
Design of the connection cable according to IEC 60 245 (H
07 RN-F) with a core cross-section of at least
−
1.5 mm
2
for cable lengths up to 25 m
−
2.5 mm
2
for cable lengths over 25 m
Long and thin connection lines result in a potential drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, plasticised PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
The connector of the connection cable must be splash-
proof.
!
Summary of Contents for ALA 2500
Page 183: ...183 ...