manualshive.com logo in svg

AT-OS AWD655-2, Instructions For Use Manual

Share
Download
AT-OS AWD655-2 Instructions For Use Manual Download Page 42

English

42

ALARM

DESCRIPTION

ACTION

E46

AIR T. LIMIT

An air temperature too high was detected.

Press RESET

If it persists, please contact a 

technician.

E47

PHASE T. LIMIT

A temperature too high was detected after 

the stage in progress.

Press RESET

If it persists, please contact a 

technician.

E50

PROBE 1 BROKEN

The PT1000-1 working probe (tank) may be 

faulty or disconnected.

Press RESET

If it persists, please contact a 

technician.

E51

PROBE 2 BROKEN

The PT1000-2 control probe (tank) may be 

faulty or disconnected.

Press RESET

If it persists, please contact a 

technician.

E52

AIR PROBE KO

The PT1000-3 probe (air) may be faulty or 

disconnected.

Press RESET

If it persists, please contact a 

technician.

E53

TANK T. DIFF.

A temperature difference too high between 

the probes in the tank was detected.

Press RESET

If it persists, please contact a 

technician.

E62

BUS CABLE

A faulty connection has been detected  

on the bus between the Micro-1 and Micro-2 

boards.

Press RESET

If it persists, please contact a 

technician.

E66

NO HEAT

There is a problem with the water heating.

Press RESET

If it persists, please contact a 

technician.

E67

CONDENSER L.

The water level in the steam condenser has 

reached the maximum level allowed.

Press RESET

If it persists, please contact a 

technician.

E70

PUMP PRESSURE

There may be water leaks.

Press RESET

If it persists, please contact a 

technician.

E71

HEPA FILTER

The HEPA filter may be dirty or obstructed. 

Check it.

Press RESET

If it persists, please contact a 

technician.

E75

PRODUCT 1 EMPTY

Tank 1 of the chemical liquid is empty. Add 

liquid.

Press RESET

If it persists, please contact a 

technician.

E76

PRODUCT 2 EMPTY

Tank 2 of the chemical liquid is empty. Add 

liquid.

Press RESET

If it persists, please contact a 

technician.

E77

PRODUCT 3 EMPTY

Tank 3 of the chemical liquid is empty. Add 

liquid.

Press RESET

If it persists, please contact a 

technician.

E89

NO DISINFECTION

The minimum value of A0 has not been rea-

ched and the load is still contaminated.

Press RESET

If it persists, please contact a 

technician.

Summary of Contents for AWD655-2













































Reviews:

No comments

Brands by name

Popular brands

Load more brands